PA66 101 NC010 Nylon66 自润滑性_产品资讯

PA66 101 NC010 Nylon66 注射速度：高速（对于增强型材料应稍低一些）。流道和浇口：由于PA66的凝固时间很短，因此浇口的位置非常重要。浇口孔径不要小于0.5t（这里t为塑件厚度）。如果使用热流道，浇口尺寸应比使用常规流道小一些，因为热流道能够帮助阻止材料过早凝固。如果用潜入式浇口，浇口的最小直径应当是0.75mm。典型用途 PA66更广泛应用于汽车工业、仪器壳体以及其它需要有抗冲击性和高强度要求的产品。

Physical Properties	Metric	English	Comments
物性表：
Density	0.980 g/cc	0.0354 lb/in³
	1.14 g/cc	0.0412 lb/in³	DAM; ISO 1183
Water Absorption	8.5 % @Thickness 2.00 mm	8.5 % @Thickness 0.0787 in	DAM; Sim. to ISO 62
Moisture Absorption	2.60 % @Thickness 2.00 mm	2.60 % @Thickness 0.0787 in	DAM; Sim. to ISO 62
Viscosity Test	145 cm³/g	145 cm³/g	DAM; ISO 307 1157 1628
Linear Mold Shrinkage, Flow	0.014 cm/cm	0.014 in/in	DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse	0.014 cm/cm	0.014 in/in	DAM; ISO 294-4 2577
Melt Flow	24 g/10 min @Load 1.20 kg, Temperature 275 °C	24 g/10 min @Load 2.65 lb, Temperature 527 °F	DAM; cm³/10min; ISO 1133

Mechanical Properties	Metric	English	Comments
Hardness, H358/30	85.0 MPa	12300 psi	50%RH; ISO 2039-1
	180 MPa	26100 psi	DAM; ISO 2039-1
Ball Indentation Hardness	160 MPa	23200 psi	DAM; H 961/30; ISO 2039-1
Tensile Strength, Yield	55.0 MPa	7980 psi	50%RH; ISO 527-1/-2
	82.0 MPa	11900 psi	DAM; ISO 527-1/-2
Elongation at Break	25 %	25 %	DAM; Nominal; ISO 527-1/-2
	>= 50 %	>= 50 %	50%RH; Nominal; ISO 527-1/-2
Elongation at Yield	4.5 %	4.5 %	DAM; ISO 527-1/-2
	25 %	25 %	50%RH; ISO 527-1/-2
Tensile Modulus	1.40 GPa	203 ksi	50%RH; ISO 527-1/-2
	3.10 GPa	450 ksi	DAM; ISO 527-1/-2
Flexural Modulus	1.20 GPa	174 ksi	50%RH; ISO 178
	2.80 GPa	406 ksi	DAM; ISO 178
Izod Impact, Notched (ISO)	5.50 kJ/m²	2.62 ft-lb/in²	DAM; ISO 180/1A
	12.0 kJ/m²	5.71 ft-lb/in²	50%RH; ISO 180/1A
	5.50 kJ/m² @Temperature -30.0 °C	2.62 ft-lb/in² @Temperature -22.0 °F	DAM; ISO 180/1A
	5.50 kJ/m² @Temperature -40.0 °C	2.62 ft-lb/in² @Temperature -40.0 °F	DAM; ISO 180/1A
Izod Impact, Unnotched (ISO)	NB	NB	DAM; ISO 180/1U
	NB	NB	50%RH; ISO 180/1U
	300 kJ/m² @Temperature -30.0 °C	143 ft-lb/in² @Temperature -22.0 °F	DAM; ISO 180/1U
Charpy Impact Unnotched	NB	NB	DAM; ISO 179/1eU
	NB	NB	50%RH; ISO 179/1eU
	40.0 J/cm² @Temperature -30.0 °C	190 ft-lb/in² @Temperature -22.0 °F	DAM; ISO 179/1eU
	NB @Temperature -30.0 °C	NB @Temperature -22.0 °F	50%RH; ISO 179/1eU
Charpy Impact, Notched	0.550 J/cm²	2.62 ft-lb/in²	DAM; ISO 179/1eA
	1.50 J/cm²	7.14 ft-lb/in²	50%RH; ISO 179/1eA
	0.300 J/cm² @Temperature -30.0 °C	1.43 ft-lb/in² @Temperature -22.0 °F	50%RH; ISO 179/1eA
	0.450 J/cm² @Temperature -30.0 °C	2.14 ft-lb/in² @Temperature -22.0 °F	DAM; ISO 179/1eA
Tensile Creep Modulus, 1 hour	1200 MPa @Time 3600 sec	174000 psi @Time 1.00 hour	50%RH; ISO 899-1
Tensile Creep Modulus, 1000 hours	700 MPa @Time 3.60e+6 sec	102000 psi @Time 1000 hour	50%RH; ISO 899-1

Electrical Properties	Metric	English	Comments
Volume Resistivity	1.00e+13 ohm-cm	1.00e+13 ohm-cm	50%RH; IEC 60093
	1.00e+15 ohm-cm	1.00e+15 ohm-cm	DAM; IEC 60093
Surface Resistance	1.00e+12 ohm	1.00e+12 ohm	50%RH; IEC 60093
Dielectric Constant	3.5 @Frequency 1.00e+6 Hz	3.5 @Frequency 1.00e+6 Hz	DAM; IEC 60250
	3.8 @Frequency 100 Hz	3.8 @Frequency 100 Hz	DAM; IEC 60250
	4.0 @Frequency 1.00e+6 Hz	4.0 @Frequency 1.00e+6 Hz	50%RH; IEC 60250
	6.0 @Frequency 100 Hz	6.0 @Frequency 100 Hz	50%RH; IEC 60250
Dielectric Strength	28.0 kV/mm	711 kV/in	50%RH; IEC 60243-1
	32.0 kV/mm	813 kV/in	DAM; IEC 60243-1
Dissipation Factor	0.0080 @Frequency 100 Hz	0.0080 @Frequency 100 Hz	DAM; IEC 60250
	0.018 @Frequency 1.00e+6 Hz	0.018 @Frequency 1.00e+6 Hz	DAM; IEC 60250
	0.075 @Frequency 1.00e+6 Hz	0.075 @Frequency 1.00e+6 Hz	50%RH; IEC 60250
	0.21 @Frequency 100 Hz	0.21 @Frequency 100 Hz	50%RH; IEC 60250

Thermal Properties	Metric	English	Comments
CTE, linear, Parallel to Flow	100 µm/m-°C	55.6 µin/in-°F	DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow	110 µm/m-°C	61.1 µin/in-°F	DAM; ISO 11359-1/-2
Specific Heat Capacity	2.79 J/g-°C	0.667 BTU/lb-°F
Thermal Conductivity	0.160 W/m-K	1.11 BTU-in/hr-ft²-°F	of melt
Melting Point	262 °C	504 °F	DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 0.46 MPa (66 psi)	200 °C	392 °F	DAM; ISO 75-1/-2
Deflection Temperature at 1.8 MPa (264 psi)	70.0 °C	158 °F	DAM; ISO 75-1/-2
Vicat Softening Point	240 °C	464 °F	DAM; 50°C/h 50N; ISO 306
Glass Transition Temp, Tg	60.0 °C	140 °F	DAM; 10°C/min; ISO 11357-1/-2
Flammability, UL94	V-2 @Thickness 1.50 mm	V-2 @Thickness 0.0591 in	DAM; IEC 60695-11-10
	V-2 @Thickness 0.700 mm	V-2 @Thickness 0.0276 in	DAM; IEC 60695-11-10
Oxygen Index	28 %	28 %	DAM; ISO 4589-1/-2

Descriptive Properties
Delivery form	Pellets
Eff. thermal diffusivity	5.00E-08 m²/s
Part Marking Code	>PA66<	ISO 11469
Processing	Injection Moulding
Regional Availability	Asia Pacific
	Europe
	Global
	Near East/Africa
	North America
	South and Central America
Resin Identification	PA66

PA66的收缩率在1%~2%之间，加入玻璃纤维添加剂可以将收缩率降低到0.2%~1% 。收缩率在流程方向和与流程方向相垂直方向上的相异是较大的。PA66对许多溶剂具有抗溶性，但对酸和其它一些氯化剂的抵抗力较弱。

上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。

PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。

欢迎各位客户前来咨询：

联系人：夏先生

手机：13501802636

QQ ：205730283

邮箱：205730283@qq.com

颗粒：