塑胶原料之家
  1. 首页
  2. 资讯
  3. 产品资讯
  4. PA66 FR70G25V0 NC010 耐冲击性特优

PA66 FR70G25V0 NC010 耐冲击性特优

PA66 FR70G25V0 NC010 透明或不透明乳白色结晶形聚合物，具有可塑性。PA66 FR70G25V0 NC010 密度1．15g/cm3。熔点252℃。脆化温度-30℃。热分解温度大于350℃。PA66 FR70G25V0 NC010 连续耐热80-120℃,平衡吸水率2．5%。能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀。 上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。 PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、
 PA66 FR70G25V0 NC010 在产品设计时，一定要考虑吸湿性对几何稳定性的影响。为了提高PA66的机械特性，经常加入各种各样的改性剂。玻璃就是最常见的添加剂，有时为了提高抗冲击性还加入合成橡胶，如EPDM和SBR等。PA66的粘性较低，因此流动性很好（但不如PA6）。这个性质可以用来加工很薄的元件。它的粘度对温度变化很敏感。
 物性表：
Physical Properties Metric English Comments
Density  1.35 g/cc 0.0488 lb/in³  
  1.49 g/cc 0.0538 lb/in³ DAM; ISO 1183
Water Absorption  3.4 %
@Thickness 2.00 mm		 3.4 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Moisture Absorption  0.900 %
@Thickness 2.00 mm		 0.900 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Viscosity    85365.8 cP
@Shear Rate 5000 1/s,
Temperature 280 °C		 85365.8 cP
@Shear Rate 5000 1/s,
Temperature 536 °F		 ISO 11403-1 -2
  138896 cP
@Shear Rate 5000 1/s,
Temperature 270 °C		 138896 cP
@Shear Rate 5000 1/s,
Temperature 518 °F		 ISO 11403-1 -2
  243435 cP
@Shear Rate 5000 1/s,
Temperature 260 °C		 243435 cP
@Shear Rate 5000 1/s,
Temperature 500 °F		 ISO 11403-1 -2
  270750 cP
@Shear Rate 500 1/s,
Temperature 280 °C		 270750 cP
@Shear Rate 500 1/s,
Temperature 536 °F		 ISO 11403-1 -2
  441615 cP
@Shear Rate 500 1/s,
Temperature 270 °C		 441615 cP
@Shear Rate 500 1/s,
Temperature 518 °F		 ISO 11403-1 -2
  774772 cP
@Shear Rate 500 1/s,
Temperature 260 °C		 774772 cP
@Shear Rate 500 1/s,
Temperature 500 °F		 ISO 11403-1 -2
Viscosity Test  140 cm³/g 140 cm³/g DAM; ISO 307 1157 1628
Linear Mold Shrinkage, Flow  0.0020 cm/cm 0.0020 in/in DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse  0.010 cm/cm 0.010 in/in DAM; ISO 294-4 2577
 
Mechanical Properties Metric English Comments
Tensile Strength at Break  110 MPa 16000 psi 50%RH; ISO 527-1/-2
  125 MPa 18100 psi DAM; ISO 527-1/-2
Tensile Stress    8.79 MPa
@Strain 0.230 %,
Temperature 150 °C		 1270 psi
@Strain 0.230 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  12.0 MPa
@Strain 0.240 %,
Temperature 90.0 °C		 1740 psi
@Strain 0.240 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  15.95 MPa
@Strain 0.470 %,
Temperature 150 °C		 2313 psi
@Strain 0.470 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  22.76 MPa
@Strain 0.480 %,
Temperature 90.0 °C		 3301 psi
@Strain 0.480 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  24.06 MPa
@Strain 0.700 %,
Temperature 150 °C		 3490 psi
@Strain 0.700 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  25.92 MPa
@Strain 0.400 %,
Temperature 40.0 °C		 3759 psi
@Strain 0.400 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  31.12 MPa
@Strain 1.10 %,
Temperature 150 °C		 4514 psi
@Strain 1.10 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  34.25 MPa
@Strain 0.790 %,
Temperature 90.0 °C		 4968 psi
@Strain 0.790 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  37.13 MPa
@Strain 0.540 %,
Temperature 40.0 °C		 5385 psi
@Strain 0.540 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  41.37 MPa
@Strain 0.570 %,
Temperature 23.0 °C		 6000 psi
@Strain 0.570 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  41.5 MPa
@Strain 0.470 %,
Temperature 23.0 °C		 6020 psi
@Strain 0.470 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  42.25 MPa
@Strain 1.55 %,
Temperature 150 °C		 6128 psi
@Strain 1.55 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  44.11 MPa
@Strain 2.01 %,
Temperature 150 °C		 6398 psi
@Strain 2.01 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  44.88 MPa
@Strain 1.15 %,
Temperature 90.0 °C		 6509 psi
@Strain 1.15 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  52.61 MPa
@Strain 3.26 %,
Temperature 150 °C		 7630 psi
@Strain 3.26 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  54.28 MPa
@Strain 0.980 %,
Temperature 40.0 °C		 7873 psi
@Strain 0.980 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  55.02 MPa
@Strain 2.75 %,
Temperature 150 °C		 7980 psi
@Strain 2.75 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  57.51 MPa
@Strain 1.63 %,
Temperature 90.0 °C		 8341 psi
@Strain 1.63 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  63.12 MPa
@Strain 2.08 %,
Temperature 90.0 °C		 9155 psi
@Strain 2.08 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  63.72 MPa
@Strain 0.650 %,
Temperature -20.0 °C		 9242 psi
@Strain 0.650 %,
Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
  67.98 MPa
@Strain 0.820 %,
Temperature 0.000 °C		 9860 psi
@Strain 0.820 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  71.93 MPa
@Strain 3.50 %,
Temperature 90.0 °C		 10430 psi
@Strain 3.50 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  72.3 MPa
@Strain 0.770 %,
Temperature 0.000 °C		 10500 psi
@Strain 0.770 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  73.4 MPa
@Strain 1.26 %,
Temperature 40.0 °C		 10600 psi
@Strain 1.26 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  73.91 MPa
@Strain 1.18 %,
Temperature 23.0 °C		 10720 psi
@Strain 1.18 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  74.49 MPa
@Strain 2.80 %,
Temperature 90.0 °C		 10800 psi
@Strain 2.80 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  78.89 MPa
@Strain 0.830 %,
Temperature -20.0 °C		 11440 psi
@Strain 0.830 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  79.11 MPa
@Strain 1.75 %,
Temperature 40.0 °C		 11470 psi
@Strain 1.75 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  84.04 MPa
@Strain 1.04 %,
Temperature 23.0 °C		 12190 psi
@Strain 1.04 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  94.42 MPa
@Strain 2.82 %,
Temperature 40.0 °C		 13690 psi
@Strain 2.82 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  100.33 MPa
@Strain 1.96 %,
Temperature 23.0 °C		 14552 psi
@Strain 1.96 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  100.68 MPa
@Strain 1.34 %,
Temperature 0.000 °C		 14602 psi
@Strain 1.34 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  100.92 MPa
@Strain 2.18 %,
Temperature 40.0 °C		 14637 psi
@Strain 2.18 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  101.62 MPa
@Strain 1.11 %,
Temperature -20.0 °C		 14739 psi
@Strain 1.11 %,
Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
  118.66 MPa
@Strain 1.78 %,
Temperature 23.0 °C		 17210 psi
@Strain 1.78 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  120.54 MPa
@Strain 1.46 %,
Temperature 0.000 °C		 17483 psi
@Strain 1.46 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  127.28 MPa
@Strain 1.98 %,
Temperature 0.000 °C		 18460 psi
@Strain 1.98 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  134.63 MPa
@Strain 1.66 %,
Temperature -20.0 °C		 19526 psi
@Strain 1.66 %,
Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
  142.85 MPa
@Strain 1.74 %,
Temperature -20.0 °C		 20719 psi
@Strain 1.74 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  157.09 MPa
@Strain 2.33 %,
Temperature 0.000 °C		 22784 psi
@Strain 2.33 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
Elongation at Break  2.0 % 2.0 % DAM; ISO 527-1/-2
  2.6 % 2.6 % 50%RH; ISO 527-1/-2
Tensile Modulus  7.50 GPa 1090 ksi 50%RH; ISO 527-1/-2
  9.00 GPa 1310 ksi DAM; ISO 527-1/-2
   3.213 GPa
@Temperature 150 °C		 466.0 ksi
@Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3.595 GPa
@Temperature 150 °C		 521.4 ksi
@Temperature 302 °F		 DAM; ISO 11403-1 -2
  5.515 GPa
@Temperature 60.0 °C		 799.9 ksi
@Temperature 140 °F		 50%RH; ISO 11403-1 -2
  5.62 GPa
@Temperature 60.0 °C		 815 ksi
@Temperature 140 °F		 DAM; ISO 11403-1 -2
  10.386 GPa
@Temperature -20.0 °C		 1506.4 ksi
@Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
  10.498 GPa
@Temperature -20.0 °C		 1522.6 ksi
@Temperature -4.00 °F		 DAM; ISO 11403-1 -2
Secant Modulus    4.15971 GPa
@Strain 2.06 %,
Temperature 40.0 °C		 603.324 ksi
@Strain 2.06 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  4.23373 GPa
@Strain 2.55 %,
Temperature 40.0 °C		 614.060 ksi
@Strain 2.55 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  4.70132 GPa
@Strain 2.28 %,
Temperature 23.0 °C		 681.879 ksi
@Strain 2.28 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  5.53878 GPa
@Strain 0.980 %,
Temperature 40.0 °C		 803.345 ksi
@Strain 0.980 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  5.8254 GPa
@Strain 1.26 %,
Temperature 40.0 °C		 844.92 ksi
@Strain 1.26 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  6.03901 GPa
@Strain 2.23 %,
Temperature 0.000 °C		 875.898 ksi
@Strain 2.23 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  6.11962 GPa
@Strain 2.09 %,
Temperature 23.0 °C		 887.590 ksi
@Strain 2.09 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  6.26356 GPa
@Strain 1.18 %,
Temperature 23.0 °C		 908.467 ksi
@Strain 1.18 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6.48 GPa
@Strain 0.400 %,
Temperature 40.0 °C		 940 ksi
@Strain 0.400 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  6.87593 GPa
@Strain 0.540 %,
Temperature 40.0 °C		 997.285 ksi
@Strain 0.540 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  7.25789 GPa
@Strain 0.570 %,
Temperature 23.0 °C		 1052.68 ksi
@Strain 0.570 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  7.51343 GPa
@Strain 1.34 %,
Temperature 0.000 °C		 1089.75 ksi
@Strain 1.34 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  7.7123 GPa
@Strain 1.87 %,
Temperature -20.0 °C		 1118.6 ksi
@Strain 1.87 %,
Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
  8.08077 GPa
@Strain 1.04 %,
Temperature 23.0 °C		 1172.03 ksi
@Strain 1.04 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  8.20977 GPa
@Strain 1.74 %,
Temperature -20.0 °C		 1190.74 ksi
@Strain 1.74 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  8.25616 GPa
@Strain 1.46 %,
Temperature 0.000 °C		 1197.47 ksi
@Strain 1.46 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  8.29024 GPa
@Strain 0.820 %,
Temperature 0.000 °C		 1202.42 ksi
@Strain 0.820 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  8.82979 GPa
@Strain 0.470 %,
Temperature 23.0 °C		 1280.67 ksi
@Strain 0.470 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  9.15496 GPa
@Strain 1.11 %,
Temperature -20.0 °C		 1327.84 ksi
@Strain 1.11 %,
Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
  9.38961 GPa
@Strain 0.770 %,
Temperature 0.000 °C		 1361.87 ksi
@Strain 0.770 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  9.50482 GPa
@Strain 0.830 %,
Temperature -20.0 °C		 1378.58 ksi
@Strain 0.830 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  9.80308 GPa
@Strain 0.650 %,
Temperature -20.0 °C		 1421.84 ksi
@Strain 0.650 %,
Temperature -4.00 °F		 50%RH; ISO 11403-1 -2
Izod Impact, Notched (ISO)  6.50 kJ/m² 3.09 ft-lb/in² DAM; ISO 180/1A
   6.00 kJ/m²
@Temperature -30.0 °C		 2.86 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1A
Charpy Impact Unnotched  4.30 J/cm² 20.5 ft-lb/in² DAM; ISO 179/1eU
   4.50 J/cm²
@Temperature -30.0 °C		 21.4 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eU
Charpy Impact, Notched  1.00 J/cm² 4.76 ft-lb/in² DAM; ISO 179/1eA
   0.900 J/cm²
@Temperature -30.0 °C		 4.28 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eA
 
Electrical Properties Metric English Comments
Volume Resistivity  1.00e+17 ohm-cm 1.00e+17 ohm-cm DAM; ASTM D257
Surface Resistance  1.00e+13 ohm 1.00e+13 ohm 50%RH; IEC 60093
  1.00e+14 ohm 1.00e+14 ohm DAM; ASTM D257
Dielectric Constant    3.4
@Frequency 1.00e+6 Hz		 3.4
@Frequency 1.00e+6 Hz		 DAM; ASTM D150
  3.5
@Frequency 1000 Hz		 3.5
@Frequency 1000 Hz		 DAM; ASTM D150
Dielectric Strength  26.0 kV/mm 660 kV/in 50%RH; IEC 60243-1
  37.0 kV/mm 940 kV/in DAM; IEC 60243-1
Dissipation Factor    0.010
@Frequency 1.00e+6 Hz		 0.010
@Frequency 1.00e+6 Hz		 DAM; ASTM D150
  0.010
@Frequency 1000 Hz		 0.010
@Frequency 1000 Hz		 DAM; ASTM D150
Comparative Tracking Index  325 V 325 V 50%RH; IEC 60112
  350 V 350 V DAM; IEC 60112
   250 - 400 V
@Thickness 3.00 mm		 250 - 400 V
@Thickness 0.118 in		 DAM; UL 746A
  250 - 400 V
@Thickness 3.00 mm		 250 - 400 V
@Thickness 0.118 in		 50%RH; UL 746A
 
Thermal Properties Metric English Comments
CTE, linear, Parallel to Flow  26.0 µm/m-°C 14.4 µin/in-°F DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow  83.0 µm/m-°C 46.1 µin/in-°F DAM; ISO 11359-1/-2
Specific Heat Capacity  1.91 J/g-°C 0.457 BTU/lb-°F  
Thermal Conductivity  0.220 W/m-K 1.53 BTU-in/hr-ft²-°F of melt
Melting Point  260 °C 500 °F DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 1.8 MPa (264 psi)  243 °C 469 °F DAM; ISO 75-1/-2
Vicat Softening Point  235 °C 455 °F DAM; 50°C/h 50N; ISO 306
UL RTI, Mechanical with Impact     65.0 °C
@Thickness 0.400 mm		 149 °F
@Thickness 0.0157 in		 UL 746B
  120 °C
@Thickness 0.800 mm		 248 °F
@Thickness 0.0315 in		 UL 746B
  120 °C
@Thickness 1.50 mm		 248 °F
@Thickness 0.0591 in		 DAM; UL 746B
  120 °C
@Thickness 3.00 mm		 248 °F
@Thickness 0.118 in		 UL 746B
UL RTI, Mechanical without Impact    65.0 °C
@Thickness 0.400 mm		 149 °F
@Thickness 0.0157 in		 UL 746B
  130 °C
@Thickness 0.800 mm		 266 °F
@Thickness 0.0315 in		 UL 746B
  130 °C
@Thickness 1.50 mm		 266 °F
@Thickness 0.0591 in		 DAM; UL 746B
  130 °C
@Thickness 3.00 mm		 266 °F
@Thickness 0.118 in		 UL 746B
Flammability, UL94    V-0
@Thickness 1.50 mm		 V-0
@Thickness 0.0591 in		 DAM; IEC 60695-11-10
  V-0
@Thickness 0.800 mm		 V-0
@Thickness 0.0315 in		 DAM; IEC 60695-11-10
  5VA
@Thickness 1.50 mm		 5VA
@Thickness 0.0591 in		 DAM; IEC 60695-11-20
 
Descriptive Properties
Additives Release agent  
Delivery form Pellets  
Emission of organic compounds 4.7 µgC/g VDA 277
Odour class 4.5 VDA 270
Part Marking Code >PA66-GF25FR(17)< ISO 11469
Processing Injection Moulding  
Regional Availability Europe  
  Near East/Africa  
Resin Identification PA66-GF25FR(17)  
UL recognition UL DAM
  UL DAM
 
B颗粒04尼龙是最重要的工程塑料，产量在五大通用工程塑料中居首位。   尼龙,是聚酰胺纤维（锦纶）是一种说法. 可制成长纤或短纤。,  工程塑料:玻璃纤维增强尼龙66(PA66+GF30) 
上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各位客户前来咨询：
联系人： 夏先生  
手  机：13501802636   
QQ    ：205730283  
邮 箱 ：205730283@qq.com 

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/news/

本文链接: http://www.su-jiao.com/news/show-25571.html

免责声明: 本文 PA66 FR70G25V0 NC010 耐冲击性特优 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他资讯信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4