PA66 FG101L NC010 耐磨性佳

 PA66 FG101L NC010 尼龙是最重要的工程塑料，产量在五大通用工程塑料中居首位。   尼龙,是聚酰胺纤维（锦纶）是一种说法. 可制成长纤或短纤。,  工程塑料:玻璃纤维增强尼龙66(PA66+GF30) 

物性表：
Physical Properties	Metric	English	Comments
Density	0.970 g/cc	0.0350 lb/in³
	1.14 g/cc	0.0412 lb/in³	DAM; ISO 1183
Water Absorption	8.5 % @Thickness 2.00 mm	8.5 % @Thickness 0.0787 in	DAM; Sim. to ISO 62
Moisture Absorption	2.60 % @Thickness 2.00 mm	2.60 % @Thickness 0.0787 in	DAM; Sim. to ISO 62
Viscosity Test	150 cm³/g	150 cm³/g	DAM; ISO 307 1157 1628
Linear Mold Shrinkage, Flow	0.014 cm/cm	0.014 in/in	DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse	0.014 cm/cm	0.014 in/in	DAM; ISO 294-4 2577
Mechanical Properties	Metric	English	Comments
Hardness, Rockwell M	59	59	50%RH; ISO 2039-2
	79	79	DAM; ISO 2039-2
Hardness, Rockwell R	108	108	50%RH; ISO 2039-2
	121	121	DAM; ISO 2039-2
Tensile Strength, Yield	55.0 MPa	7980 psi	50%RH; ISO 527-1/-2
	82.0 MPa	11900 psi	DAM; ISO 527-1/-2
Elongation at Break	25 %	25 %	DAM; Nominal; ISO 527-1/-2
	>= 50 %	>= 50 %	50%RH; Nominal; ISO 527-1/-2
Elongation at Yield	4.5 %	4.5 %	DAM; ISO 527-1/-2
	4.5 %	4.5 %	DAM; ISO 527-3
	25 %	25 %	50%RH; ISO 527-1/-2
Tensile Modulus	1.40 GPa	203 ksi	50%RH; ISO 527-1/-2
	3.10 GPa	450 ksi	DAM; ISO 527-1/-2
Flexural Modulus	1.20 GPa	174 ksi	50%RH; ISO 178
	2.80 GPa	406 ksi	DAM; ISO 178
Charpy Impact Unnotched	NB	NB	DAM; ISO 179/1eU
	NB	NB	50%RH; ISO 179/1eU
	40.0 J/cm² @Temperature -30.0 °C	190 ft-lb/in² @Temperature -22.0 °F	DAM; ISO 179/1eU
	NB @Temperature -30.0 °C	NB @Temperature -22.0 °F	50%RH; ISO 179/1eU
Charpy Impact, Notched	0.550 J/cm²	2.62 ft-lb/in²	DAM; ISO 179/1eA
	1.50 J/cm²	7.14 ft-lb/in²	50%RH; ISO 179/1eA
	0.300 J/cm² @Temperature -30.0 °C	1.43 ft-lb/in² @Temperature -22.0 °F	50%RH; ISO 179/1eA
	0.450 J/cm² @Temperature -30.0 °C	2.14 ft-lb/in² @Temperature -22.0 °F	DAM; ISO 179/1eA
Tensile Creep Modulus, 1 hour	1400 MPa @Time 3600 sec	203000 psi @Time 1.00 hour	50%RH; ISO 899-1
Tensile Creep Modulus, 1000 hours	820 MPa @Time 3.60e+6 sec	119000 psi @Time 1000 hour	50%RH; ISO 899-1
Electrical Properties	Metric	English	Comments
Volume Resistivity	1.00e+12 ohm-cm	1.00e+12 ohm-cm	50%RH; IEC 60093
	1.00e+14 ohm-cm	1.00e+14 ohm-cm	DAM; IEC 60093
Surface Resistance	1.00e+12 ohm	1.00e+12 ohm	50%RH; IEC 60093
Dielectric Constant	3.5 @Frequency 1.00e+6 Hz	3.5 @Frequency 1.00e+6 Hz	DAM; IEC 60250
	3.8 @Frequency 100 Hz	3.8 @Frequency 100 Hz	DAM; IEC 60250
	4.0 @Frequency 1.00e+6 Hz	4.0 @Frequency 1.00e+6 Hz	50%RH; IEC 60250
	6.0 @Frequency 100 Hz	6.0 @Frequency 100 Hz	50%RH; IEC 60250
Dielectric Strength	28.0 kV/mm	711 kV/in	50%RH; IEC 60243-1
	32.0 kV/mm	813 kV/in	DAM; IEC 60243-1
Dissipation Factor	0.0080 @Frequency 100 Hz	0.0080 @Frequency 100 Hz	DAM; IEC 60250
	0.018 @Frequency 1.00e+6 Hz	0.018 @Frequency 1.00e+6 Hz	DAM; IEC 60250
	0.075 @Frequency 1.00e+6 Hz	0.075 @Frequency 1.00e+6 Hz	50%RH; IEC 60250
	0.21 @Frequency 100 Hz	0.21 @Frequency 100 Hz	50%RH; IEC 60250
Comparative Tracking Index	600 V	600 V	DAM; IEC 60112
Thermal Properties	Metric	English	Comments
CTE, linear, Parallel to Flow	100 µm/m-°C	55.6 µin/in-°F	DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow	110 µm/m-°C	61.1 µin/in-°F	DAM; ISO 11359-1/-2
Specific Heat Capacity	2.79 J/g-°C	0.667 BTU/lb-°F
Thermal Conductivity	0.160 W/m-K	1.11 BTU-in/hr-ft²-°F	of melt
Melting Point	262 °C	504 °F	DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 0.46 MPa (66 psi)	200 °C	392 °F	DAM; ISO 75-1/-2
Deflection Temperature at 1.8 MPa (264 psi)	70.0 °C	158 °F	DAM; ISO 75-1/-2
Vicat Softening Point	240 °C	464 °F	DAM; 50°C/h 50N; ISO 306
Glass Transition Temp, Tg	60.0 °C	140 °F	DAM; 10°C/min; ISO 11357-1/-2
Flammability, UL94	V-2 @Thickness 1.50 mm	V-2 @Thickness 0.0591 in	DAM; IEC 60695-11-10
	V-2 @Thickness 0.700 mm	V-2 @Thickness 0.0276 in	DAM; IEC 60695-11-10
Oxygen Index	28 %	28 %	DAM; ISO 4589-1/-2
Descriptive Properties
Additives	Release agent
Delivery form	Pellets
Eff. thermal diffusivity	5.00E-08 m²/s
Part Marking Code	>PA66<	ISO 11469
Processing	Injection Moulding
Regional Availability	Asia Pacific
	Europe
	Global
	Near East/Africa
	North America
	South and Central America
Resin Identification	PA66
UL recognition	UL	DAM

在产品设计时，一定要考虑吸湿性对几何稳定性的影响。为了提高PA66的机械特性，经常加入各种各样的改性剂。玻璃就是最常见的添加剂，有时为了提高抗冲击性还加入合成橡胶，如EPDM和SBR等。PA66的粘性较低，因此流动性很好（但不如PA6）。