Overview of materials for Nylon 66, 50% Glass Fiber Filled

Overview of materials for Nylon 66, 50% Glass Fiber Filled 物性表: Overview of materials for Nylon 66, 50% Glass Fiber Filled物性表及特性介绍,Overview of materials for Nylon 66, 50% Glass Fiber Filled注塑参数详情,如需Overview of materials for Nylon 66, 50% Glass Fiber Filled下载, 可到相关下载区下载
  • 熔体流动速率 [g/10min]: 1.0
  • 密度 [g/cm3]: 1.45
  • 吸水率 [%]: 0.3
  • 缺口冲击强度: 1.01
  • 拉伸强度 [MPa]: 130.0
  • 断裂伸长率 [%]: 216
  • 弯曲强度 [MPa]: 37.4
  • 弯曲模量 [MPa]: 7.90
  • 硬度: 98.0
  • 热变形温度 [℃]: 240.0
 
Physical PropertiesMetricEnglishComments
Density 1.45 - 1.78 g/cc0.0524 - 0.0643 lb/in³Average value: 1.57 g/cc Grade Count:116
Filler Content 45.0 - 50.0 %45.0 - 50.0 %Average value: 49.2 % Grade Count:19
Water Absorption 0.300 - 4.30 %0.300 - 4.30 %Average value: 1.83 % Grade Count:68
Moisture Absorption at Equilibrium 0.170 - 2.00 %0.170 - 2.00 %Average value: 1.15 % Grade Count:34
Water Absorption at Saturation 0.200 - 7.00 %0.200 - 7.00 %Average value: 3.61 % Grade Count:9
Viscosity  20.0 - 450 cP
@Temperature 280 - 300 °C
20.0 - 450 cP
@Temperature 536 - 572 °F
Average value: 197 cP Grade Count:1
 20.0 - 450 cP
@Shear Rate 10.0 - 1000 1/s
20.0 - 450 cP
@Shear Rate 10.0 - 1000 1/s
Average value: 197 cP Grade Count:1
Viscosity Measurement 0.560 - 1450.560 - 145Average value: 118 Grade Count:14
Viscosity Test 131 - 150 cm³/g131 - 150 cm³/gAverage value: 139 cm³/g Grade Count:8
Maximum Moisture Content 0.0900 - 0.9000.0900 - 0.900Average value: 0.360 Grade Count:3
Linear Mold Shrinkage 0.00100 - 0.0200 cm/cm0.00100 - 0.0200 in/inAverage value: 0.00329 cm/cm Grade Count:92
Linear Mold Shrinkage, 6.35 mm section 0.00400 cm/cm0.00400 in/inAverage value: 0.00400 cm/cm Grade Count:4
Linear Mold Shrinkage, Transverse 0.00150 - 0.0116 cm/cm0.00150 - 0.0116 in/inAverage value: 0.00698 cm/cm Grade Count:34
Melt Flow 1.00 - 40.0 g/10 min1.00 - 40.0 g/10 minAverage value: 19.5 g/10 min Grade Count:17
 
Mechanical PropertiesMetricEnglishComments
Hardness, Rockwell M 80.0 - 10080.0 - 100Average value: 93.7 Grade Count:5
Hardness, Rockwell R 98.0 - 12598.0 - 125Average value: 120 Grade Count:33
Ball Indentation Hardness 131 - 340 MPa19000 - 49300 psiAverage value: 307 MPa Grade Count:10
Tensile Strength, Ultimate 37.4 - 299 MPa5420 - 43400 psiAverage value: 201 MPa Grade Count:70
 95.0 - 342.669 MPa
@Temperature -40.0 - 149 °C
13800 - 49700.1 psi
@Temperature -40.0 - 300 °F
Average value: 112 MPa Grade Count:6
 90.0 - 125 MPa
@Temperature 130 - 175 °C
13100 - 18100 psi
@Temperature 266 - 347 °F
Average value: 112 MPa Grade Count:2
 90.0 - 125 MPa
@Time 1.80e+7 - 7.20e+7 sec
13100 - 18100 psi
@Time 5000 - 20000 hour
Average value: 112 MPa Grade Count:2
 12.62 - 299.36 MPa
@Strain 0.220 - 6.93 %
1830 - 43419 psi
@Strain 0.220 - 6.93 %
Average value: 112 MPa Grade Count:1
 12.62 - 299.36 MPa
@Temperature -20.0 - 220 °C
1830 - 43419 psi
@Temperature -4.00 - 428 °F
Average value: 112 MPa Grade Count:1
Tensile Strength, Yield 130 - 265 MPa18900 - 38400 psiAverage value: 211 MPa Grade Count:46
 131 - 131 MPa
@Temperature 93.3 - 93.3 °C
19000 - 19000 psi
@Temperature 200 - 200 °F
Average value: 131 MPa Grade Count:1
Elongation at Break 1.00 - 5.00 %1.00 - 5.00 %Average value: 2.43 % Grade Count:95
 1.80 - 2.70 %
@Temperature -40.0 - 149 °C
1.80 - 2.70 %
@Temperature -40.0 - 300 °F
Average value: 2.25 % Grade Count:3
Elongation at Yield 1.00 - 3.70 %1.00 - 3.70 %Average value: 2.63 % Grade Count:13
Modulus of Elasticity 10.2 - 18.7 GPa1480 - 2710 ksiAverage value: 15.7 GPa Grade Count:73
 5.818 - 19.788 GPa
@Temperature -40.0 - 200 °C
843.8 - 2870.0 ksi
@Temperature -40.0 - 392 °F
Average value: 11.0 GPa Grade Count:5
Flexural Yield Strength 216 - 425 MPa31300 - 61600 psiAverage value: 326 MPa Grade Count:86
 175 - 455.054 MPa
@Temperature -40.0 - 149 °C
25400 - 66000.1 psi
@Temperature -40.0 - 300 °F
Average value: 264 MPa Grade Count:6
Flexural Modulus 7.90 - 17.2 GPa1150 - 2500 ksiAverage value: 13.8 GPa Grade Count:92
 6.50 - 19.0985 GPa
@Temperature -40.0 - 149 °C
943 - 2770.04 ksi
@Temperature -40.0 - 300 °F
Average value: 9.85 GPa Grade Count:9
Shear Modulus 0.100 - 3.00 GPa
@Temperature 0.000 - 350 °C
14.5 - 435 ksi
@Temperature 32.0 - 662 °F
Average value: 1.34 GPa Grade Count:1
Izod Impact, Notched 1.01 - 6.51 J/cm1.90 - 12.2 ft-lb/inAverage value: 1.94 J/cm Grade Count:57
 1.10 - 7.36782 J/cm
@Temperature -40.0 - 149 °C
2.06 - 13.8029 ft-lb/in
@Temperature -40.0 - 300 °F
Average value: 2.61 J/cm Grade Count:4
Izod Impact, Unnotched 9.61 - 70.0 J/cm18.0 - 131 ft-lb/inAverage value: 15.3 J/cm Grade Count:23
Izod Impact, Notched (ISO) 12.0 - 25.0 kJ/m²5.71 - 11.9 ft-lb/in²Average value: 15.7 kJ/m² Grade Count:20
 11.0 - 15.0 kJ/m²
@Temperature -30.0 - -30.0 °C
5.23 - 7.14 ft-lb/in²
@Temperature -22.0 - -22.0 °F
Average value: 13.0 kJ/m² Grade Count:6
Izod Impact, Unnotched (ISO) 54.0 - 103 kJ/m²25.7 - 49.0 ft-lb/in²Average value: 86.8 kJ/m² Grade Count:4
 47.0 - 96.0 kJ/m²
@Temperature -30.0 - -30.0 °C
22.4 - 45.7 ft-lb/in²
@Temperature -22.0 - -22.0 °F
Average value: 80.8 kJ/m² Grade Count:4
Charpy Impact Unnotched 5.20 J/cm² - NB24.7 ft-lb/in² - NBAverage value: 8.56 J/cm² Grade Count:48
 4.60 J/cm² - NB
@Temperature -40.0 - 30.0 °C
21.9 ft-lb/in² - NB
@Temperature -40.0 - 86.0 °F
Average value: 7.93 J/cm² Grade Count:32
Charpy Impact, Notched 0.500 - 4.70 J/cm²2.38 - 22.4 ft-lb/in²Average value: 1.88 J/cm² Grade Count:49
 0.350 - 4.50 J/cm²
@Temperature -40.0 - 30.0 °C
1.67 - 21.4 ft-lb/in²
@Temperature -40.0 - 86.0 °F
Average value: 1.38 J/cm² Grade Count:29
Dart Drop, Total Energy  9.99 - 23.5 J
@Temperature -20.0 - -20.0 °C
7.37 - 17.3 ft-lb
@Temperature -4.00 - -4.00 °F
Average value: 16.7 J Grade Count:1
 9.99 - 23.5 J
@Thickness 3.18 - 3.18 mm
7.37 - 17.3 ft-lb
@Thickness 0.125 - 0.125 in
Average value: 16.7 J Grade Count:1
Puncture Energy 2.80 - 23.8 J
@Temperature -30.0 - -30.0 °C
2.07 - 17.6 ft-lb
@Temperature -22.0 - -22.0 °F
Average value: 9.80 J Grade Count:2
Tensile Creep Modulus, 1000 hours 5400 - 8000 MPa783000 - 1.16e+6 psiAverage value: 7360 MPa Grade Count:5
 
Electrical PropertiesMetricEnglishComments
Electrical Resistivity 1.00e+10 - 1.00e+17 ohm-cm1.00e+10 - 1.00e+17 ohm-cmAverage value: 3.06e+15 ohm-cm Grade Count:60
Surface Resistance 1.00e+10 - 1.00e+16 ohm1.00e+10 - 1.00e+16 ohmAverage value: 3.30e+14 ohm Grade Count:35
Dielectric Constant 3.50 - 14.03.50 - 14.0Average value: 4.99 Grade Count:25
Dielectric Strength 1.97 - 90.0 kV/mm50.0 - 2290 kV/inAverage value: 34.3 kV/mm Grade Count:46
Dissipation Factor 0.00900 - 0.3200.00900 - 0.320Average value: 0.0815 Grade Count:17
Arc Resistance 93.0 - 135 sec93.0 - 135 secAverage value: 116 sec Grade Count:6
Comparative Tracking Index 350 - 600 V350 - 600 VAverage value: 534 V Grade Count:38
Hot Wire Ignition, HWI 1.00 - 30.0 sec1.00 - 30.0 secAverage value: 17.1 sec Grade Count:4
High Amp Arc Ignition, HAI 1.00 - 120 arcs1.00 - 120 arcsAverage value: 90.3 arcs Grade Count:4
 
Thermal PropertiesMetricEnglishComments
CTE, linear 0.0500 - 500 µm/m-°C0.0278 - 278 µin/in-°FAverage value: 31.3 µm/m-°C Grade Count:41
CTE, linear, Transverse to Flow 0.500 - 88.0 µm/m-°C0.278 - 48.9 µin/in-°FAverage value: 47.1 µm/m-°C Grade Count:14
Specific Heat Capacity 1.30 J/g-°C0.311 BTU/lb-°FAverage value: 1.30 J/g-°C Grade Count:6
Thermal Conductivity 0.350 - 0.533 W/m-K2.43 - 3.70 BTU-in/hr-ft²-°FAverage value: 0.387 W/m-K Grade Count:9
Melting Point 220 - 325 °C428 - 617 °FAverage value: 265 °C Grade Count:66
Maximum Service Temperature, Air 100 - 250 °C212 - 482 °FAverage value: 180 °C Grade Count:25
Deflection Temperature at 0.46 MPa (66 psi) 240 - 263 °C464 - 505 °FAverage value: 255 °C Grade Count:55
Deflection Temperature at 1.8 MPa (264 psi) 210 - 285 °C410 - 545 °FAverage value: 253 °C Grade Count:97
Deflection Temperature at 8.0 MPa 175 - 249 °C347 - 480 °FAverage value: 213 °C Grade Count:12
Vicat Softening Point 200 - 260 °C392 - 500 °FAverage value: 244 °C Grade Count:22
Decomposition Temperature 310 °C590 °FAverage value: 310 °C Grade Count:6
UL RTI, Electrical 115 - 120 °C239 - 248 °FAverage value: 119 °C Grade Count:5
UL RTI, Mechanical with Impact 110 - 130 °C230 - 266 °FAverage value: 114 °C Grade Count:3
UL RTI, Mechanical without Impact 115 - 130 °C239 - 266 °FAverage value: 121 °C Grade Count:3
Flammability, UL94 HB - V-0HB - V-0Grade Count:64
Oxygen Index 23.0 - 32.0 %23.0 - 32.0 %Average value: 27.3 % Grade Count:10
Glow Wire Test 649 - 960 °C1200 - 1760 °FAverage value: 750 °C Grade Count:15
Shrinkage  0.100 - 0.100 %
@Temperature 120 - 120 °C
0.100 - 0.100 %
@Temperature 248 - 248 °F
Average value: 0.100 % Grade Count:1
 0.100 - 0.100 %
@Time 14400 - 14400 sec
0.100 - 0.100 %
@Time 4.00 - 4.00 hour
Average value: 0.100 % Grade Count:1
 
Processing PropertiesMetricEnglishComments
Processing Temperature 70.0 - 310 °C158 - 590 °FAverage value: 156 °C Grade Count:26
Feed Temperature 20.0 - 275 °C68.0 - 527 °FAverage value: 78.2 °C Grade Count:14
Nozzle Temperature 270 - 304 °C518 - 580 °FAverage value: 285 °C Grade Count:9
Die Temperature 300 - 320 °C572 - 608 °FAverage value: 311 °C Grade Count:8
Melt Temperature 143 - 325 °C290 - 617 °FAverage value: 291 °C Grade Count:52
Mold Temperature 50.0 - 124 °C122 - 255 °FAverage value: 88.2 °C Grade Count:55
Drying Temperature 70.0 - 121 °C158 - 250 °FAverage value: 81.7 °C Grade Count:45
Dry Time 2.00 - 12.0 hour2.00 - 12.0 hourAverage value: 3.72 hour Grade Count:37
 2.00 - 4.00 hour
@Temperature 79.4 - 79.4 °C
2.00 - 4.00 hour
@Temperature 175 - 175 °F
Average value: 3.00 hour Grade Count:2
Moisture Content 0.0300 - 0.200 %0.0300 - 0.200 %Average value: 0.150 % Grade Count:33
Dew Point -30.0 - -17.8 °C-22.0 - 0.000 °FAverage value: -24.6 °C Grade Count:7
Injection Pressure 4.96 - 150 MPa720 - 21800 psiAverage value: 86.5 MPa Grade Count:25
Hold Pressure 50.0 - 100 MPa7250 - 14500 psiAverage value: 70.8 MPa Grade Count:9
Back Pressure 0.345 - 58.8 MPa50.0 - 8530 psiAverage value: 13.6 MPa Grade Count:11
Screw Speed 20.0 - 100 rpm20.0 - 100 rpmAverage value: 41.3 rpm Grade Count:11
Hot-Working Temperature 300 - 315 °C572 - 599 °FAverage value: 308 °C Grade Count:4

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/wuxingbiao/

本文链接: http://www.su-jiao.com/yuanliaoku/show-44775.html

免责声明: 本文 Overview of materials for Nylon 66, 50% Glass Fiber Filled 仅代表作者个人观点,中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容,其版权均由原作者和资料提供方所拥有!如因作品版权问题需要处理,请与我们联络

塑胶原料之家,专业塑料网站、原料报价网站,免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4