- 熔体流动速率 [g/10min]: 93.8
- 密度 [g/cm3]: 1.34
- 吸水率 [%]: 6.3
- 缺口冲击强度: 8.5
- 拉伸强度 [MPa]: 60.0
- 弯曲模量 [MPa]: 3.00
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Density | 1.34 g/cc | 0.0484 lb/in³ | ISO 1183 | ||
| Water Absorption | 6.3 - 6.9 % | 6.3 - 6.9 % | ISO 62 | ||
| Moisture Absorption at Equilibrium | 1.9 - 2.3 % | 1.9 - 2.3 % | (23°C/50% R.H.); ISO 62 | ||
| Viscosity Test | 140 cm³/g | 140 cm³/g | Viscosity number | ||
| Linear Mold Shrinkage | 0.0050 cm/cm | 0.0050 in/in | |||
| Melt Flow | 93.8 g/10 min @Load 5.00 kg, Temperature 275 °C | 93.8 g/10 min @Load 11.0 lb, Temperature 527 °F | ISO 1133 | ||
| Mechanical Properties | Metric | English | Comments | ||
| Tensile Strength, Yield | 60.0 MPa | 8700 psi | 50mm/min; ISO 527 | ||
| Elongation at Yield | 15 % | 15 % | 50mm/min; ISO 527 | ||
| Modulus of Elasticity | 3.00 GPa | 435 ksi | ISO 527 | ||
| Flexural Strength | 70.0 MPa | 10200 psi | ISO 178 | ||
| Flexural Modulus | 3.00 GPa | 435 ksi | ISO 178 | ||
| Izod Impact, Notched (ISO) | 8.50 kJ/m² | 4.04 ft-lb/in² | ISO 180/A | ||
| Charpy Impact Unnotched | 9.00 J/cm² | 42.8 ft-lb/in² | ISO 179/1eU | ||
| Charpy Impact, Notched | 1.10 J/cm² | 5.24 ft-lb/in² | ISO 179/1eA | ||
| Tensile Creep Modulus, 1000 hours | 2000 MPa @Strain 0.500 % | 290000 psi @Strain 0.500 % | ISO 899-1 | ||
| Electrical Properties | Metric | English | Comments | ||
| Volume Resistivity | 1.00e+10 ohm-cm | 1.00e+10 ohm-cm | IEC 60093 | ||
| Surface Resistance | 1.00e+10 ohm | 1.00e+10 ohm | IEC 60093 | ||
| Dielectric Constant | 4.6 @Frequency 1.00e+6 Hz | 4.6 @Frequency 1.00e+6 Hz | IEC 60250 | ||
| Dissipation Factor | 0.070 @Frequency 1.00e+6 Hz | 0.070 @Frequency 1.00e+6 Hz | IEC 60250 | ||
| Comparative Tracking Index | 425 V | 425 V | Test Solution A; IEC 60112 | ||
| Thermal Properties | Metric | English | Comments | ||
| Specific Heat Capacity | 1.40 J/g-°C | 0.335 BTU/lb-°F | |||
| Thermal Conductivity | 0.340 W/m-K | 2.36 BTU-in/hr-ft²-°F | DIN 53765 | ||
| Melting Point | 220 °C | 428 °F | |||
| Maximum Service Temperature, Air | 200 °C | 392 °F | |||
| Processing Properties | Metric | English | Comments | ||
| Melt Temperature | 270 - 290 °C | 518 - 554 °F | Injection-molding/Extrusion | ||
| Mold Temperature | 80.0 - 90.0 °C | 176 - 194 °F | Injection-molding | ||
| Descriptive Properties | |||||
| Color | Natural | ||||
| Commercial Status | North America and Europe | ||||
| Form | Pellets | ||||
| Impact Modified | No | ||||
| Primary Processing Technique | Injection Molding | ||||
| Processing | Injection Molding | ||||
| Special characteristic | Heat stabilized or stable to heat | ||||