| 物性表： | |||||
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Density | 0.970 g/cc | 0.0350 lb/in³ | |||
| 1.14 g/cc | 0.0412 lb/in³ | DAM; ISO 1183 | |||
| Water Absorption | 8.5 % @Thickness 2.00 mm |
8.5 % @Thickness 0.0787 in |
DAM; Sim. to ISO 62 | ||
| Moisture Absorption | 2.60 % @Thickness 2.00 mm |
2.60 % @Thickness 0.0787 in |
DAM; Sim. to ISO 62 | ||
| Viscosity Test | 140 cm³/g | 140 cm³/g | DAM; ISO 307 1157 1628 | ||
| Linear Mold Shrinkage, Flow | 0.0020 cm/cm | 0.0020 in/in | DAM; 48h at 80°C; ISO 294-4 | ||
| 0.014 cm/cm | 0.014 in/in | DAM; ISO 294-4 2577 | |||
| Linear Mold Shrinkage, Transverse | 0.0010 cm/cm | 0.0010 in/in | DAM; 48h at 80°C; ISO 294-4 | ||
| 0.014 cm/cm | 0.014 in/in | DAM; ISO 294-4 2577 | |||
| Mechanical Properties | Metric | English | Comments | ||
| Tensile Strength, Yield | 55.0 MPa | 7980 psi | 50%RH; ISO 527-1/-2 | ||
| 82.0 MPa | 11900 psi | DAM; ISO 527-1/-2 | |||
| Elongation at Break | 20 % | 20 % | DAM; Nominal; ISO 527-1/-2 | ||
| >= 50 % | >= 50 % | 50%RH; Nominal; ISO 527-1/-2 | |||
| Elongation at Yield | 4.5 % | 4.5 % | DAM; ISO 527-1/-2 | ||
| 4.5 % | 4.5 % | DAM; ISO 527-3 | |||
| 25 % | 25 % | 50%RH; ISO 527-1/-2 | |||
| Tensile Modulus | 1.40 GPa | 203 ksi | 50%RH; ISO 527-1/-2 | ||
| 3.10 GPa | 450 ksi | DAM; ISO 527-1/-2 | |||
| 0.206713 GPa @Temperature 170 °C |
29.9812 ksi @Temperature 338 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 0.272711 GPa @Temperature 170 °C |
39.5535 ksi @Temperature 338 °F |
DAM; Dynamic; ISO 11403-1 -2 | |||
| 0.278067 GPa @Temperature 110 °C |
40.3303 ksi @Temperature 230 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 0.362001 GPa @Temperature 110 °C |
52.5039 ksi @Temperature 230 °F |
DAM; Dynamic; ISO 11403-1 -2 | |||
| 0.853069 GPa @Temperature 30.0 °C |
123.727 ksi @Temperature 86.0 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 1.63807 GPa @Temperature -20.0 °C |
237.582 ksi @Temperature -4.00 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 1.84283 GPa @Temperature 30.0 °C |
267.280 ksi @Temperature 86.0 °F |
DAM; Dynamic; ISO 11403-1 -2 | |||
| 1.94187 GPa @Temperature -20.0 °C |
281.645 ksi @Temperature -4.00 °F |
DAM; Dynamic; ISO 11403-1 -2 | |||
| 1.96576 GPa @Temperature -70.0 °C |
285.110 ksi @Temperature -94.0 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 2.24271 GPa @Temperature -100 °C |
325.278 ksi @Temperature -148 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 2.24941 GPa @Temperature -70.0 °C |
326.250 ksi @Temperature -94.0 °F |
DAM; Dynamic; ISO 11403-1 -2 | |||
| 2.53487 GPa @Temperature -100 °C |
367.652 ksi @Temperature -148 °F |
DAM; Dynamic; ISO 11403-1 -2 | |||
| Flexural Modulus | 1.20 GPa | 174 ksi | 50%RH; ISO 178 | ||
| 2.80 GPa | 406 ksi | DAM; ISO 178 | |||
| Shear Modulus | 0.1472 GPa @Temperature 160 °C |
21.35 ksi @Temperature 320 °F |
50%RH; Dynamic; ISO 11403-1 -2 | ||
| 0.1704 GPa @Temperature 120 °C |
24.71 ksi @Temperature 248 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 0.2441 GPa @Temperature 70.0 °C |
35.40 ksi @Temperature 158 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 0.6874 GPa @Temperature 20.0 °C |
99.70 ksi @Temperature 68.0 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 1.0895 GPa @Temperature -20.0 °C |
158.02 ksi @Temperature -4.00 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| 1.2168 GPa @Temperature -50.0 °C |
176.48 ksi @Temperature -58.0 °F |
50%RH; Dynamic; ISO 11403-1 -2 | |||
| Izod Impact, Notched (ISO) | 5.50 kJ/m² | 2.62 ft-lb/in² | DAM; ISO 180/1A | ||
| 11.0 kJ/m² | 5.23 ft-lb/in² | 50%RH; ISO 180/1A | |||
| 4.00 kJ/m² @Temperature -30.0 °C |
1.90 ft-lb/in² @Temperature -22.0 °F |
50%RH; ISO 180/1A | |||
| 5.50 kJ/m² @Temperature -40.0 °C |
2.62 ft-lb/in² @Temperature -40.0 °F |
DAM; ISO 180/1A | |||
| 6.00 kJ/m² @Temperature -30.0 °C |
2.86 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 180/1A | |||
| Izod Impact, Unnotched (ISO) | 300 kJ/m² | 143 ft-lb/in² | DAM; ISO 180/1U | ||
| NB | NB | 50%RH; ISO 180/1U | |||
| 300 kJ/m² @Temperature -30.0 °C |
143 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 180/1U | |||
| Charpy Impact Unnotched | NB | NB | DAM; ISO 179/1eU | ||
| NB | NB | 50%RH; ISO 179/1eU | |||
| 40.0 J/cm² @Temperature -30.0 °C |
190 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 179/1eU | |||
| NB @Temperature -30.0 °C |
NB @Temperature -22.0 °F |
50%RH; ISO 179/1eU | |||
| Charpy Impact, Notched | 0.600 J/cm² | 2.86 ft-lb/in² | DAM; ISO 179/1eA | ||
| 1.30 J/cm² | 6.19 ft-lb/in² | 50%RH; ISO 179/1eA | |||
| 0.300 J/cm² @Temperature -30.0 °C |
1.43 ft-lb/in² @Temperature -22.0 °F |
50%RH; ISO 179/1eA | |||
| 0.450 J/cm² @Temperature -30.0 °C |
2.14 ft-lb/in² @Temperature -22.0 °F |
DAM; ISO 179/1eA | |||
| Tensile Creep Modulus, 1 hour | 1400 MPa @Time 3600 sec |
203000 psi @Time 1.00 hour |
50%RH; ISO 899-1 | ||
| Tensile Creep Modulus, 1000 hours | 930 MPa @Time 3.60e+6 sec |
135000 psi @Time 1000 hour |
50%RH; ISO 899-1 | ||
| Electrical Properties | Metric | English | Comments | ||
| Volume Resistivity | 1.00e+15 ohm-cm | 1.00e+15 ohm-cm | DAM; IEC 60093 | ||
| >= 1.00e+15 ohm-cm | >= 1.00e+15 ohm-cm | 50%RH; IEC 60093 | |||
| Surface Resistance | 1.00e+12 ohm | 1.00e+12 ohm | DAM; ASTM D257 | ||
| Dielectric Constant | 3.6 @Frequency 1.00e+6 Hz |
3.6 @Frequency 1.00e+6 Hz |
DAM; IEC 60250 | ||
| 3.8 @Frequency 100 Hz |
3.8 @Frequency 100 Hz |
DAM; IEC 60250 | |||
| 4.6 @Frequency 1.00e+6 Hz |
4.6 @Frequency 1.00e+6 Hz |
50%RH; IEC 60250 | |||
| 8.0 @Frequency 100 Hz |
8.0 @Frequency 100 Hz |
50%RH; IEC 60250 | |||
| Dielectric Strength | 26.0 kV/mm | 660 kV/in | 50%RH; IEC 60243-1 | ||
| 31.5 kV/mm | 800 kV/in | DAM; IEC 60243-1 | |||
| Dissipation Factor | 0.014 @Frequency 100 Hz |
0.014 @Frequency 100 Hz |
DAM; IEC 60250 | ||
| 0.018 @Frequency 1.00e+6 Hz |
0.018 @Frequency 1.00e+6 Hz |
DAM; IEC 60250 | |||
| 0.10 @Frequency 1.00e+6 Hz |
0.10 @Frequency 1.00e+6 Hz |
50%RH; IEC 60250 | |||
| Thermal Properties | Metric | English | Comments | ||
| CTE, linear, Parallel to Flow | 100 µm/m-°C | 55.6 µin/in-°F | DAM; ISO 11359-1/-2 | ||
| CTE, linear, Transverse to Flow | 110 µm/m-°C | 61.1 µin/in-°F | DAM; ISO 11359-1/-2 | ||
| Specific Heat Capacity | 2.79 J/g-°C | 0.667 BTU/lb-°F | |||
| Thermal Conductivity | 0.160 W/m-K | 1.11 BTU-in/hr-ft²-°F | of melt | ||
| Melting Point | 262 °C | 504 °F | DAM; 10°C/min; ISO 11357-1/-3 | ||
| Deflection Temperature at 0.46 MPa (66 psi) | 200 °C | 392 °F | DAM; ISO 75-1/-2 | ||
| Deflection Temperature at 1.8 MPa (264 psi) | 70.0 °C | 158 °F | DAM; ISO 75-1/-2 | ||
| Vicat Softening Point | 240 °C | 464 °F | DAM; 50°C/h 50N; ISO 306 | ||
| Glass Transition Temp, Tg | 60.0 °C | 140 °F | DAM; 10°C/min; ISO 11357-1/-2 | ||
| Flammability, UL94 | V-2 @Thickness 1.50 mm |
V-2 @Thickness 0.0591 in |
DAM; IEC 60695-11-10 | ||
| V-2 @Thickness 0.700 mm |
V-2 @Thickness 0.0276 in |
DAM; IEC 60695-11-10 | |||
| Oxygen Index | 28 % | 28 % | DAM; ISO 4589-1/-2 | ||
| De |
|||||
| Additives | Release agent | ||||
| Delivery form | Pellets | ||||
| Eff. thermal diffusivity | 5.00E-08 m²/s | ||||
| Emission of organic compounds | 6.5 µgC/g | VDA 277 | |||
| Odour | class 3 | VDA 270 | |||
| Part Marking Code | >PA66< | ISO 11469 | |||
| Processing | Injection Moulding | ||||
| Regional Availability | Asia Pacific | ||||
| Europe | |||||
| Global | |||||
| Near East/Africa | |||||
| North America | |||||
| South and Central America | |||||
| Resin Identification | PA66 | ||||
| UL recognition | UL | DAM |
|||
熔化温度：260~290℃。对玻璃添加剂的产品为275~280℃。熔化温度应避免高于300℃。 模具温度：建议80℃。模具温度将影响结晶度，而结晶度将影响产品的物理特性。对于薄壁塑件，如果使用低于40℃的模具温度，则塑件的结晶度将随着时间而变化，为了保持塑件的几何稳定性，需要进行退火处理。
图：上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各位客户前来咨询：
联系人： 夏先生
手 机：13501802636
QQ ：205730283
邮 箱 ：205730283@qq.com