塑胶原料之家
  1. 首页
  2. 资讯
  3. 产品资讯
  4. PA66 70G33HS1L NC010 耐韧

PA66 70G33HS1L NC010 耐韧

PA66 70G33HS1L NC010 透明或不透明乳白色结晶形聚合物，具有可塑性。PA66 70G33HS1L NC010 密度1．15g/cm3。熔点252℃。脆化温度-30℃。PA66 70G33HS1L NC010 热分解温度大于350℃。 连续耐热80-120℃,平衡吸水率2．5%。能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀。
 PA66 70G33HS1L NC010 生产方法：尼龙66 由己二酸和己二胺缩聚而成。它的生产工艺主要有单体合成、尼龙66盐的制备和缩聚三个工序。
单体合成1)己二酸的制备主要有苯酚法、环己烷法和丙烯腈二聚法。苯酚法是以苯酚为原料，用雷尼镍作催化剂，在140到150℃和2到3MPa压力下，加氢生成环己醇，然后用60%到65%浓度的硝酸，在铜或钒催化剂存在下，在55到60℃氧化成己二酸。
 物性表：
Physical Properties Metric English Comments
Density  1.39 g/cc 0.0502 lb/in³ DAM; ISO 1183
Water Absorption  5.7 %
@Thickness 2.00 mm		 5.7 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Moisture Absorption  1.80 %
@Thickness 2.00 mm		 1.80 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Water Absorption at Saturation  1.2 % 1.2 % DAM; Immersion 24h; ASTM D570
Viscosity  198170 cP
@Shear Rate 500 1/s,
Temperature 295 °C		 198170 cP
@Shear Rate 500 1/s,
Temperature 563 °F		 ISO 11403-1 -2
Viscosity Test  130 cm³/g 130 cm³/g DAM; ISO 307 1157 1628
Linear Mold Shrinkage, Flow  0.0030 cm/cm 0.0030 in/in DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse  0.011 cm/cm 0.011 in/in DAM; ISO 294-4 2577
 
Mechanical Properties Metric English Comments
Tensile Strength at Break  140 MPa 20300 psi 50%RH; ISO 527-1/-2
  200 MPa 29000 psi DAM; ISO 527-1/-2
Tensile Stress    13.24 MPa
@Strain 0.300 %,
Temperature 150 °C		 1920 psi
@Strain 0.300 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  20.91 MPa
@Strain 0.200 %,
Temperature 23.0 °C		 3033 psi
@Strain 0.200 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  21.792 MPa
@Strain 0.500 %,
Temperature 150 °C		 3160.7 psi
@Strain 0.500 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  32.13 MPa
@Strain 0.500 %,
Temperature 23.0 °C		 4660 psi
@Strain 0.500 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  35.04 MPa
@Strain 0.900 %,
Temperature 150 °C		 5082 psi
@Strain 0.900 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  45.024 MPa
@Strain 1.30 %,
Temperature 150 °C		 6530.2 psi
@Strain 1.30 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  45.7 MPa
@Strain 0.400 %,
Temperature 0.000 °C		 6630 psi
@Strain 0.400 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  45.82 MPa
@Strain 0.400 %,
Temperature -40.0 °C		 6646 psi
@Strain 0.400 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  49.8 MPa
@Strain 0.500 %,
Temperature 23.0 °C		 7220 psi
@Strain 0.500 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  50.11 MPa
@Strain 1.50 %,
Temperature 150 °C		 7268 psi
@Strain 1.50 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  52.73 MPa
@Strain 0.600 %,
Temperature 0.000 °C		 7648 psi
@Strain 0.600 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  57.312 MPa
@Strain 1.90 %,
Temperature 150 °C		 8312.4 psi
@Strain 1.90 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  61.4 MPa
@Strain 2.10 %,
Temperature 150 °C		 8910 psi
@Strain 2.10 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  65.7 MPa
@Strain 0.600 %,
Temperature -40.0 °C		 9530 psi
@Strain 0.600 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  65.952 MPa
@Strain 2.50 %,
Temperature 150 °C		 9565.5 psi
@Strain 2.50 %,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  71.19 MPa
@Strain 1.30 %,
Temperature 23.0 °C		 10330 psi
@Strain 1.30 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  75.89 MPa
@Strain 0.800 %,
Temperature 23.0 °C		 11010 psi
@Strain 0.800 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  76.75 MPa
@Strain 0.700 %,
Temperature 0.000 °C		 11130 psi
@Strain 0.700 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  77.0 MPa
@Strain 0.700 %,
Temperature -40.0 °C		 11200 psi
@Strain 0.700 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  77.82 MPa
@Strain 0.900 %,
Temperature 0.000 °C		 11290 psi
@Strain 0.900 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  81.76 MPa
@Strain 4.50 %,
Temperature 150 °C		 11860 psi
@Strain 4.50 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  92.34 MPa
@Strain 1.90 %,
Temperature 23.0 °C		 13390 psi
@Strain 1.90 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  98.36 MPa
@Strain 1.20 %,
Temperature 0.000 °C		 14270 psi
@Strain 1.20 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  106.06 MPa
@Strain 1.00 %,
Temperature 0.000 °C		 15383 psi
@Strain 1.00 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  106.62 MPa
@Strain 1.00 %,
Temperature -40.0 °C		 15464 psi
@Strain 1.00 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  109.17 MPa
@Strain 2.50 %,
Temperature 23.0 °C		 15834 psi
@Strain 2.50 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  121.5 MPa
@Strain 1.40 %,
Temperature 23.0 °C		 17620 psi
@Strain 1.40 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  123.11 MPa
@Strain 1.60 %,
Temperature 0.000 °C		 17856 psi
@Strain 1.60 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  131.98 MPa
@Strain 1.30 %,
Temperature 0.000 °C		 19142 psi
@Strain 1.30 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  136.23 MPa
@Strain 1.30 %,
Temperature -40.0 °C		 19759 psi
@Strain 1.30 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  147.5 MPa
@Strain 1.50 %,
Temperature -40.0 °C		 21390 psi
@Strain 1.50 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  176.3 MPa
@Strain 1.90 %,
Temperature -40.0 °C		 25570 psi
@Strain 1.90 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  179.66 MPa
@Strain 3.40 %,
Temperature 0.000 °C		 26058 psi
@Strain 3.40 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  199.09 MPa
@Strain 3.20 %,
Temperature 23.0 °C		 28876 psi
@Strain 3.20 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  212.5 MPa
@Strain 2.50 %,
Temperature -40.0 °C		 30820 psi
@Strain 2.50 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  224.79 MPa
@Strain 3.00 %,
Temperature 0.000 °C		 32603 psi
@Strain 3.00 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  251.95 MPa
@Strain 2.90 %,
Temperature -40.0 °C		 36542 psi
@Strain 2.90 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
Elongation at Break  3.5 % 3.5 % DAM; ISO 527-1/-2
  5.0 % 5.0 % 50%RH; ISO 527-1/-2
Tensile Modulus  8.00 GPa 1160 ksi 50%RH; ISO 527-1/-2
  10.5 GPa 1520 ksi DAM; ISO 527-1/-2
Flexural Strength  200 MPa 29000 psi 50%RH; ISO 178
  290 MPa 42100 psi DAM; ISO 178
Flexural Modulus  6.21 GPa 901 ksi 50%RH; ISO 178
  9.30 GPa 1350 ksi DAM; ISO 178
Shear Strength  0.099085 MPa
@Shear Rate 500 1/s,
Temperature 295 °C		 14.371 psi
@Shear Rate 500 1/s,
Temperature 563 °F		 ISO 11403-1 -2
Secant Modulus    2.34054 GPa
@Strain 3.70 %,
Temperature 100 °C		 339.472 ksi
@Strain 3.70 %,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  2.66946 GPa
@Strain 3.70 %,
Temperature 100 °C		 387.178 ksi
@Strain 3.70 %,
Temperature 212 °F		 DAM; ISO 11403-1 -2
  2.74118 GPa
@Strain 3.40 %,
Temperature 80.0 °C		 397.581 ksi
@Strain 3.40 %,
Temperature 176 °F		 50%RH; ISO 11403-1 -2
  2.80 GPa
@Strain 2.90 %,
Temperature 100 °C		 406 ksi
@Strain 2.90 %,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  2.91079 GPa
@Strain 3.80 %,
Temperature 80.0 °C		 422.181 ksi
@Strain 3.80 %,
Temperature 176 °F		 DAM; ISO 11403-1 -2
  3.23846 GPa
@Strain 2.60 %,
Temperature 80.0 °C		 469.706 ksi
@Strain 2.60 %,
Temperature 176 °F		 50%RH; ISO 11403-1 -2
  3.2868 GPa
@Strain 2.50 %,
Temperature 100 °C		 476.72 ksi
@Strain 2.50 %,
Temperature 212 °F		 DAM; ISO 11403-1 -2
  3.30476 GPa
@Strain 2.10 %,
Temperature 100 °C		 479.322 ksi
@Strain 2.10 %,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3.41514 GPa
@Strain 3.70 %,
Temperature 23.0 °C		 495.332 ksi
@Strain 3.70 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  3.71583 GPa
@Strain 2.40 %,
Temperature 80.0 °C		 538.944 ksi
@Strain 2.40 %,
Temperature 176 °F		 DAM; ISO 11403-1 -2
  3.76667 GPa
@Strain 1.80 %,
Temperature 80.0 °C		 546.318 ksi
@Strain 1.80 %,
Temperature 176 °F		 50%RH; ISO 11403-1 -2
  3.82471 GPa
@Strain 1.70 %,
Temperature 100 °C		 554.736 ksi
@Strain 1.70 %,
Temperature 212 °F		 DAM; ISO 11403-1 -2
  3.87692 GPa
@Strain 1.30 %,
Temperature 100 °C		 562.308 ksi
@Strain 1.30 %,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  4.06241 GPa
@Strain 2.90 %,
Temperature 23.0 °C		 589.212 ksi
@Strain 2.90 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  4.33625 GPa
@Strain 1.60 %,
Temperature 80.0 °C		 628.930 ksi
@Strain 1.60 %,
Temperature 176 °F		 DAM; ISO 11403-1 -2
  4.41 GPa
@Strain 1.00 %,
Temperature 80.0 °C		 640 ksi
@Strain 1.00 %,
Temperature 176 °F		 50%RH; ISO 11403-1 -2
  4.62333 GPa
@Strain 0.900 %,
Temperature 100 °C		 670.568 ksi
@Strain 0.900 %,
Temperature 212 °F		 DAM; ISO 11403-1 -2
  4.64 GPa
@Strain 0.500 %,
Temperature 100 °C		 673 ksi
@Strain 0.500 %,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  4.69286 GPa
@Strain 2.10 %,
Temperature 23.0 °C		 680.652 ksi
@Strain 2.10 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  5.27875 GPa
@Strain 0.800 %,
Temperature 80.0 °C		 765.630 ksi
@Strain 0.800 %,
Temperature 176 °F		 DAM; ISO 11403-1 -2
  5.47615 GPa
@Strain 1.30 %,
Temperature 23.0 °C		 794.261 ksi
@Strain 1.30 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  5.70 GPa
@Strain 0.200 %,
Temperature 80.0 °C		 827 ksi
@Strain 0.200 %,
Temperature 176 °F		 50%RH; ISO 11403-1 -2
  5.94667 GPa
@Strain 0.300 %,
Temperature 100 °C		 862.505 ksi
@Strain 0.300 %,
Temperature 212 °F		 DAM; ISO 11403-1 -2
  6.03357 GPa
@Strain 2.80 %,
Temperature 0.000 °C		 875.109 ksi
@Strain 2.80 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  6.426 GPa
@Strain 0.500 %,
Temperature 23.0 °C		 932.0 ksi
@Strain 0.500 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6.885 GPa
@Strain 0.200 %,
Temperature 80.0 °C		 998.6 ksi
@Strain 0.200 %,
Temperature 176 °F		 DAM; ISO 11403-1 -2
  7.01731 GPa
@Strain 2.60 %,
Temperature 23.0 °C		 1017.79 ksi
@Strain 2.60 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  7.109 GPa
@Strain 2.00 %,
Temperature 0.000 °C		 1031 ksi
@Strain 2.00 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  8.10154 GPa
@Strain 1.30 %,
Temperature 0.000 °C		 1175.05 ksi
@Strain 1.30 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  8.12444 GPa
@Strain 1.80 %,
Temperature 23.0 °C		 1178.37 ksi
@Strain 1.80 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  8.25556 GPa
@Strain 2.70 %,
Temperature -40.0 °C		 1197.39 ksi
@Strain 2.70 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  8.44375 GPa
@Strain 2.40 %,
Temperature 0.000 °C		 1224.68 ksi
@Strain 2.40 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  8.64667 GPa
@Strain 0.900 %,
Temperature 0.000 °C		 1254.11 ksi
@Strain 0.900 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  8.78833 GPa
@Strain 0.600 %,
Temperature 0.000 °C		 1274.66 ksi
@Strain 0.600 %,
Temperature 32.0 °F		 50%RH; ISO 11403-1 -2
  9.15 GPa
@Strain 2.00 %,
Temperature -40.0 °C		 1330 ksi
@Strain 2.00 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  9.231 GPa
@Strain 1.00 %,
Temperature 23.0 °C		 1339 ksi
@Strain 1.00 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  9.47636 GPa
@Strain 2.20 %,
Temperature -40.0 °C		 1374.45 ksi
@Strain 2.20 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  9.7025 GPa
@Strain 1.60 %,
Temperature 0.000 °C		 1407.3 ksi
@Strain 1.60 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  9.83333 GPa
@Strain 1.50 %,
Temperature -40.0 °C		 1426.23 ksi
@Strain 1.50 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  9.96 GPa
@Strain 0.500 %,
Temperature 23.0 °C		 1440 ksi
@Strain 0.500 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  10.2067 GPa
@Strain 1.50 %,
Temperature -40.0 °C		 1480.38 ksi
@Strain 1.50 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  10.4509 GPa
@Strain 1.10 %,
Temperature 0.000 °C		 1515.80 ksi
@Strain 1.10 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  10.455 GPa
@Strain 0.200 %,
Temperature 23.0 °C		 1516.4 ksi
@Strain 0.200 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  10.5873 GPa
@Strain 1.10 %,
Temperature -40.0 °C		 1535.58 ksi
@Strain 1.10 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  10.95 GPa
@Strain 0.600 %,
Temperature -40.0 °C		 1588 ksi
@Strain 0.600 %,
Temperature -40.0 °F		 50%RH; ISO 11403-1 -2
  10.9643 GPa
@Strain 0.700 %,
Temperature 0.000 °C		 1590.26 ksi
@Strain 0.700 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  11.0 GPa
@Strain 0.700 %,
Temperature -40.0 °C		 1600 ksi
@Strain 0.700 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
  11.425 GPa
@Strain 0.400 %,
Temperature 0.000 °C		 1657.1 ksi
@Strain 0.400 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  11.455 GPa
@Strain 0.400 %,
Temperature -40.0 °C		 1661.4 ksi
@Strain 0.400 %,
Temperature -40.0 °F		 DAM; ISO 11403-1 -2
Izod Impact, Notched (ISO)  12.0 kJ/m² 5.71 ft-lb/in² DAM; ISO 180/1A
  15.0 kJ/m² 7.14 ft-lb/in² 50%RH; ISO 180/1A
   10.0 kJ/m²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1A
  10.0 kJ/m²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 180/1A
  10.0 kJ/m²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 DAM; ISO 180/1A
  10.0 kJ/m²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 50%RH; ISO 180/1A
Izod Impact, Unnotched (ISO)  80.0 kJ/m² 38.1 ft-lb/in² DAM; ISO 180/1U
  90.0 kJ/m² 42.8 ft-lb/in² 50%RH; ISO 180/1U
   70.0 kJ/m²
@Temperature -30.0 °C		 33.3 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1U
  70.0 kJ/m²
@Temperature -30.0 °C		 33.3 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 180/1U
Charpy Impact Unnotched  8.50 J/cm² 40.4 ft-lb/in² DAM; ISO 179/1eU
  10.0 J/cm² 47.6 ft-lb/in² 50%RH; ISO 179/1eU
   7.00 J/cm²
@Temperature -30.0 °C		 33.3 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eU
  7.50 J/cm²
@Temperature -30.0 °C		 35.7 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 179/1eU
Charpy Impact, Notched  1.30 J/cm² 6.19 ft-lb/in² DAM; ISO 179/1eA
  1.70 J/cm² 8.09 ft-lb/in² 50%RH; ISO 179/1eA
   1.00 J/cm²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eA
  1.00 J/cm²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 179/1eA
  1.00 J/cm²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 DAM; ISO 179/1eA
  1.00 J/cm²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 50%RH; ISO 179/1eA
Tensile Creep Modulus, 1 hour  8000 MPa
@Time 3600 sec		 1.16e+6 psi
@Time 1.00 hour		 50%RH; ISO 899-1
Tensile Creep Modulus, 1000 hours  5500 MPa
@Time 3.60e+6 sec		 798000 psi
@Time 1000 hour		 50%RH; ISO 899-1
 
Electrical Properties Metric English Comments
Volume Resistivity  1.00e+11 ohm-cm 1.00e+11 ohm-cm 50%RH; IEC 60093
  1.00e+15 ohm-cm 1.00e+15 ohm-cm DAM; IEC 60093
Surface Resistance  1.00e+15 ohm 1.00e+15 ohm 50%RH; IEC 60093
Dielectric Constant    3.7
@Frequency 1.00e+6 Hz		 3.7
@Frequency 1.00e+6 Hz		 DAM; ASTM D150
  4.0
@Frequency 1.00e+6 Hz		 4.0
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  4.2
@Frequency 100 Hz		 4.2
@Frequency 100 Hz		 DAM; IEC 60250
  4.5
@Frequency 1000 Hz		 4.5
@Frequency 1000 Hz		 DAM; ASTM D150
Dissipation Factor    0.010
@Frequency 100 Hz		 0.010
@Frequency 100 Hz		 DAM; IEC 60250
  0.015
@Frequency 1.00e+6 Hz		 0.015
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  0.020
@Frequency 1.00e+6 Hz		 0.020
@Frequency 1.00e+6 Hz		 DAM; ASTM D150
Comparative Tracking Index  400 V 400 V DAM; IEC 60112
  400 - 600 V
@Thickness 3.00 mm		 400 - 600 V
@Thickness 0.118 in		 DAM; UL 746A
 
Thermal Properties Metric English Comments
CTE, linear, Parallel to Flow  18.0 µm/m-°C 10.0 µin/in-°F DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow  83.0 µm/m-°C 46.1 µin/in-°F DAM; ISO 11359-1/-2
Specific Heat Capacity  1.33 J/g-°C 0.318 BTU/lb-°F  
  2.21 J/g-°C 0.528 BTU/lb-°F  
Thermal Conductivity  0.220 W/m-K 1.53 BTU-in/hr-ft²-°F of melt
Melting Point  262 °C 504 °F DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 0.46 MPa (66 psi)  261 °C 502 °F DAM; ISO 75-1/-2
Deflection Temperature at 1.8 MPa (264 psi)  252 °C 486 °F DAM; ISO 75-1/-2
Glass Transition Temp, Tg  80.0 °C 176 °F DAM; 10°C/min; ISO 11357-1/-2
Flammability, UL94    HB
@Thickness 1.50 mm		 HB
@Thickness 0.0591 in		 DAM; IEC 60695-11-10
  HB
@Thickness 0.800 mm		 HB
@Thickness 0.0315 in		 DAM; IEC 60695-11-10
Flame Spread  28 mm/min
@Thickness 1.00 mm		 1.1 in/min
@Thickness 0.0394 in		 SE/B; ISO 3795 (FMVSS 302)
Oxygen Index  24 % 24 % DAM; ISO 4589-1/-2
 
Descriptive Properties
Additives Lubricants  
  Release agent  
Delivery form Pellets  
Emission of organic compounds 6 µgC/g VDA 277
Part Marking Code >PA66-GF33< ISO 11469
Processing Injection Moulding  
Regional Availability Asia Pacific  
  Europe  
  Global  
  Near East/Africa  
  North America  
  South and Central America  
Resin Identification PA66-GF33  
Special characteristics Heat stabilised or stable to heat  
UL recognition UL DAM
  UL DAM
 
具有优良的耐磨性、自润滑性，机械强度较高。但吸水性较大，因而尺寸稳定性较差
颗粒07
上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各位客户前来咨询：
联系人： 夏先生  
手  机：13501802636   
QQ    ：205730283  
邮 箱 ：205730283@qq.com 
 

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/news/

本文链接: http://www.su-jiao.com/news/show-25494.html

免责声明: 本文 PA66 70G33HS1L NC010 耐韧 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他资讯信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4