塑胶原料之家
  1. 首页
  2. 资讯
  3. 产品资讯
  4. PA66 70G33L NC010 耐冲击性特优

PA66 70G33L NC010 耐冲击性特优

PA66 70G33L NC010 的收缩率在1%~2%之间，PA66 70G33L NC010 加入玻璃纤维添加剂可以将收缩率降低到0.2%~1% 。PA66 70G33L NC010 收缩率在流程方向和与流程方向相垂直方向上的相异是较大的。PA66对许多溶剂具有抗溶性，但对酸和其它一些氯化剂的抵抗力较弱。
 PA66 70G33L NC010 在产品设计时，一定要考虑吸湿性对几何稳定性的影响。为了提高PA66的机械特性，经常加入各种各样的改性剂。玻璃就是最常见的添加剂，有时为了提高抗冲击性还加入合成橡胶，如EPDM和SBR等。PA66的粘性较低，因此流动性很好（但不如PA6）。这个性质可以用来加工很薄的元件。它的粘度对温度变化很敏感。
物性表：
Physical Properties Metric English Comments
Density  1.39 g/cc 0.0502 lb/in³ DAM; ISO 1183
Water Absorption  5.7 %
@Thickness 2.00 mm		 5.7 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Moisture Absorption  1.80 %
@Thickness 2.00 mm		 1.80 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Water Absorption at Saturation  1.2 % 1.2 % DAM; Immersion 24h; ASTM D570
Viscosity Test  145 cm³/g 145 cm³/g DAM; ISO 307 1157 1628
Linear Mold Shrinkage, Flow  0.0030 cm/cm 0.0030 in/in DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse  0.011 cm/cm 0.011 in/in DAM; ISO 294-4 2577
 
Mechanical Properties Metric English Comments
Tensile Strength at Break  140 MPa 20300 psi 50%RH; ISO 527-1/-2
  200 MPa 29000 psi DAM; ISO 527-1/-2
Tensile Stress    10.0 MPa
@Strain 0.120 %,
Time 3600 sec		 1450 psi
@Strain 0.120 %,
Time 1.00 hour		 50%RH; isochronous; ISO 11403-1 -2
  10.0 MPa
@Strain 0.125 %,
Time 36000 sec		 1450 psi
@Strain 0.125 %,
Time 10.0 hour		 50%RH; isochronous; ISO 11403-1 -2
  10.0 MPa
@Strain 0.130 %,
Time 360000 sec		 1450 psi
@Strain 0.130 %,
Time 100 hour		 50%RH; isochronous; ISO 11403-1 -2
  10.0 MPa
@Strain 0.150 %,
Time 3.60e+6 sec		 1450 psi
@Strain 0.150 %,
Time 1000 hour		 50%RH; isochronous; ISO 11403-1 -2
Elongation at Break  3.5 % 3.5 % DAM; ISO 527-1/-2
  5.0 % 5.0 % 50%RH; ISO 527-1/-2
Tensile Modulus  8.00 GPa 1160 ksi 50%RH; ISO 527-1/-2
  10.5 GPa 1520 ksi DAM; ISO 527-1/-2
Flexural Strength  200 MPa 29000 psi 50%RH; ISO 178
  290 MPa 42100 psi DAM; ISO 178
Flexural Modulus  6.21 GPa 901 ksi 50%RH; ISO 178
  9.30 GPa 1350 ksi DAM; ISO 178
Izod Impact, Notched (ISO)  12.0 kJ/m² 5.71 ft-lb/in² DAM; ISO 180/1A
  15.0 kJ/m² 7.14 ft-lb/in² 50%RH; ISO 180/1A
   10.0 kJ/m²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1A
  10.0 kJ/m²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 180/1A
  10.0 kJ/m²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 DAM; ISO 180/1A
  10.0 kJ/m²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 50%RH; ISO 180/1A
Izod Impact, Unnotched (ISO)  80.0 kJ/m² 38.1 ft-lb/in² DAM; ISO 180/1U
  90.0 kJ/m² 42.8 ft-lb/in² 50%RH; ISO 180/1U
   70.0 kJ/m²
@Temperature -30.0 °C		 33.3 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1U
  70.0 kJ/m²
@Temperature -30.0 °C		 33.3 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 180/1U
Charpy Impact Unnotched  8.50 J/cm² 40.4 ft-lb/in² DAM; ISO 179/1eU
  10.0 J/cm² 47.6 ft-lb/in² 50%RH; ISO 179/1eU
   7.00 J/cm²
@Temperature -30.0 °C		 33.3 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eU
  7.50 J/cm²
@Temperature -30.0 °C		 35.7 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 179/1eU
Charpy Impact, Notched  1.30 J/cm² 6.19 ft-lb/in² DAM; ISO 179/1eA
  1.70 J/cm² 8.09 ft-lb/in² 50%RH; ISO 179/1eA
   1.00 J/cm²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eA
  1.00 J/cm²
@Temperature -30.0 °C		 4.76 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 179/1eA
  1.00 J/cm²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 DAM; ISO 179/1eA
  1.00 J/cm²
@Temperature -40.0 °C		 4.76 ft-lb/in²
@Temperature -40.0 °F		 50%RH; ISO 179/1eA
Tensile Creep Modulus, 1 hour    3191.49 MPa
@Pressure 30.0 MPa,
Temperature 150 °C		 462887 psi
@Pressure 4350 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3211.23 MPa
@Pressure 25.0 MPa,
Temperature 150 °C		 465750 psi
@Pressure 3630 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3235.47 MPa
@Pressure 20.0 MPa,
Temperature 150 °C		 469266 psi
@Pressure 2900 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3260.87 MPa
@Pressure 15.0 MPa,
Temperature 150 °C		 472950 psi
@Pressure 2180 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3280.68 MPa
@Pressure 10.0 MPa,
Temperature 150 °C		 475823 psi
@Pressure 1450 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3292.68 MPa
@Pressure 5.00 MPa,
Temperature 150 °C		 477564 psi
@Pressure 725 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  3571.43 MPa
@Pressure 25.0 MPa,
Temperature 100 °C		 517993 psi
@Pressure 3630 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3571.43 MPa
@Pressure 30.0 MPa,
Temperature 100 °C		 517993 psi
@Pressure 4350 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3571.43 MPa
@Pressure 5.00 MPa,
Temperature 100 °C		 517993 psi
@Pressure 725 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3571.43 MPa
@Pressure 10.0 MPa,
Temperature 100 °C		 517993 psi
@Pressure 1450 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3571.43 MPa
@Pressure 15.0 MPa,
Temperature 100 °C		 517993 psi
@Pressure 2180 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3571.43 MPa
@Pressure 20.0 MPa,
Temperature 100 °C		 517993 psi
@Pressure 2900 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  8108.11 MPa
@Pressure 30.0 MPa,
Temperature 23.0 °C		 1.17598e+6 psi
@Pressure 4350 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  8150.79 MPa
@Pressure 25.0 MPa,
Temperature 23.0 °C		 1.18217e+6 psi
@Pressure 3630 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  8205.13 MPa
@Pressure 20.0 MPa,
Temperature 23.0 °C		 1.19006e+6 psi
@Pressure 2900 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  8268.73 MPa
@Pressure 15.0 MPa,
Temperature 23.0 °C		 1.19928e+6 psi
@Pressure 2180 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  8333.33 MPa
@Pressure 10.0 MPa,
Temperature 23.0 °C		 1.20865e+6 psi
@Pressure 1450 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  8376.96 MPa
@Pressure 5.00 MPa,
Temperature 23.0 °C		 1.21498e+6 psi
@Pressure 725 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  8000 MPa
@Time 3600 sec		 1.16e+6 psi
@Time 1.00 hour		 50%RH; ISO 899-1
Tensile Creep Modulus, 1000 hours    2678.57 MPa
@Pressure 30.0 MPa,
Temperature 150 °C		 388494 psi
@Pressure 4350 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  2692.46 MPa
@Pressure 25.0 MPa,
Temperature 150 °C		 390509 psi
@Pressure 3630 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  2709.48 MPa
@Pressure 20.0 MPa,
Temperature 150 °C		 392978 psi
@Pressure 2900 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  2727.27 MPa
@Pressure 15.0 MPa,
Temperature 150 °C		 395558 psi
@Pressure 2180 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  2741.12 MPa
@Pressure 10.0 MPa,
Temperature 150 °C		 397567 psi
@Pressure 1450 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  2749.49 MPa
@Pressure 5.00 MPa,
Temperature 150 °C		 398781 psi
@Pressure 725 psi,
Temperature 302 °F		 50%RH; ISO 11403-1 -2
  2941.18 MPa
@Pressure 30.0 MPa,
Temperature 100 °C		 426583 psi
@Pressure 4350 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  2957.93 MPa
@Pressure 25.0 MPa,
Temperature 100 °C		 429012 psi
@Pressure 3630 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  2978.49 MPa
@Pressure 20.0 MPa,
Temperature 100 °C		 431994 psi
@Pressure 2900 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3000 MPa
@Pressure 15.0 MPa,
Temperature 100 °C		 435000 psi
@Pressure 2180 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3016.76 MPa
@Pressure 10.0 MPa,
Temperature 100 °C		 437545 psi
@Pressure 1450 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  3026.91 MPa
@Pressure 5.00 MPa,
Temperature 100 °C		 439017 psi
@Pressure 725 psi,
Temperature 212 °F		 50%RH; ISO 11403-1 -2
  6250 MPa
@Pressure 30.0 MPa,
Temperature 23.0 °C		 906000 psi
@Pressure 4350 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6326.61 MPa
@Pressure 25.0 MPa,
Temperature 23.0 °C		 917599 psi
@Pressure 3630 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6425.7 MPa
@Pressure 20.0 MPa,
Temperature 23.0 °C		 931970 psi
@Pressure 2900 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6543.97 MPa
@Pressure 15.0 MPa,
Temperature 23.0 °C		 949124 psi
@Pressure 2180 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6666.67 MPa
@Pressure 10.0 MPa,
Temperature 23.0 °C		 966920 psi
@Pressure 1450 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  6751.05 MPa
@Pressure 5.00 MPa,
Temperature 23.0 °C		 979159 psi
@Pressure 725 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  5500 MPa
@Time 3.60e+6 sec		 798000 psi
@Time 1000 hour		 50%RH; ISO 899-1
 
Electrical Properties Metric English Comments
Volume Resistivity  1.00e+15 ohm-cm 1.00e+15 ohm-cm DAM; IEC 60093
Dielectric Constant    4.0
@Frequency 1.00e+6 Hz		 4.0
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  4.2
@Frequency 100 Hz		 4.2
@Frequency 100 Hz		 DAM; IEC 60250
Dissipation Factor    0.010
@Frequency 100 Hz		 0.010
@Frequency 100 Hz		 DAM; IEC 60250
  0.015
@Frequency 1.00e+6 Hz		 0.015
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
Comparative Tracking Index  600 V 600 V DAM; IEC 60112
 
Thermal Properties Metric English Comments
CTE, linear, Parallel to Flow  18.0 µm/m-°C 10.0 µin/in-°F DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow  83.0 µm/m-°C 46.1 µin/in-°F DAM; ISO 11359-1/-2
Specific Heat Capacity  1.33 J/g-°C 0.318 BTU/lb-°F C
  2.21 J/g-°C 0.528 BTU/lb-°F  
Thermal Conductivity  0.220 W/m-K 1.53 BTU-in/hr-ft²-°F of melt
Melting Point  262 °C 504 °F DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 0.46 MPa (66 psi)  261 °C 502 °F DAM; ISO 75-1/-2
Deflection Temperature at 1.8 MPa (264 psi)  252 °C 486 °F DAM; ISO 75-1/-2
Glass Transition Temp, Tg  80.0 °C 176 °F DAM; 10°C/min; ISO 11357-1/-2
Flammability, UL94  HB
@Thickness 0.700 mm		 HB
@Thickness 0.0276 in		 DAM; IEC 60695-11-10
Flame Spread  28 mm/min
@Thickness 1.00 mm		 1.1 in/min
@Thickness 0.0394 in		 SE/B; ISO 3795 (FMVSS 302)
Oxygen Index  24 % 24 % DAM; ISO 4589-1/-2
 
Descriptive Properties
Additives Lubricants  
  Release agent  
Delivery form Pellets  
Part Marking Code >PA66-GF33< ISO 11469
Processing Injection Moulding  
Regional Availability Asia Pacific  
  Europe  
  Global  
  Near East/Africa  
  North America  
  South and Central America  
Resin Identification PA66-GF33
 
优点：
1、具高抗张强度；2、耐韧、耐冲击性特优；3、自润性、耐磨性佳、耐药品性优；4、低温特性佳；5、具自熄性；
用途:
广泛应用于机械、仪器仪表、汽车部件、电子电气、铁路、家电、通讯、纺机、体育休闲用品、油管、油箱及一些精密工程制品。
颗粒08
上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各位客户前来咨询：
联系人： 夏先生  
手  机：13501802636   
QQ    ：205730283  
邮 箱 ：205730283@qq.com 

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/news/

本文链接: http://www.su-jiao.com/news/show-25498.html

免责声明: 本文 PA66 70G33L NC010 耐冲击性特优 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他资讯信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4