塑胶原料之家
  1. 首页
  2. 资讯
  3. 产品资讯
  4. PA66 103HSL NC010 低温特性佳

PA66 103HSL NC010 低温特性佳

PA66 103HSL NC010 透明或不透明乳白色结晶形聚合物，具有可塑性PA66 103HSL NC010。密度1．15g/cm3。熔点252℃。脆化温度-30℃。热分解温度大于350℃。PA66 103HSL NC010 连续耐热80-120℃,平衡吸水率2．5%。能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀。
 PA66 103HSL NC010 在产品设计时，一定要考虑吸湿性对几何稳定性的影响。为了提高PA66的机械特性，经常加入各种各样的改性剂。玻璃就是最常见的添加剂，有时为了提高抗冲击性还加入合成橡胶，如EPDM和SBR等。PA66的粘性较低，因此流动性很好（但不如PA6）。这个性质可以用来加工很薄的元件。它的粘度对温度变化很敏感。
 物性表：
Physical Properties Metric English Comments
Density  0.980 g/cc 0.0354 lb/in³  
  1.14 g/cc 0.0412 lb/in³ DAM; ISO 1183
Water Absorption  8.5 %
@Thickness 2.00 mm		 8.5 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Moisture Absorption  2.60 %
@Thickness 2.00 mm		 2.60 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Viscosity    43967.3 cP
@Shear Rate 5000 1/s,
Temperature 300 °C		 43967.3 cP
@Shear Rate 5000 1/s,
Temperature 572 °F		 ISO 11403-1 -2
  51428.2 cP
@Shear Rate 5000 1/s,
Temperature 290 °C		 51428.2 cP
@Shear Rate 5000 1/s,
Temperature 554 °F		 ISO 11403-1 -2
  60010.9 cP
@Shear Rate 5000 1/s,
Temperature 280 °C		 60010.9 cP
@Shear Rate 5000 1/s,
Temperature 536 °F		 ISO 11403-1 -2
  100011 cP
@Shear Rate 500 1/s,
Temperature 300 °C		 100011 cP
@Shear Rate 500 1/s,
Temperature 572 °F		 ISO 11403-1 -2
  134064 cP
@Shear Rate 500 1/s,
Temperature 290 °C		 134064 cP
@Shear Rate 500 1/s,
Temperature 554 °F		 ISO 11403-1 -2
  180250 cP
@Shear Rate 500 1/s,
Temperature 280 °C		 180250 cP
@Shear Rate 500 1/s,
Temperature 536 °F		 ISO 11403-1 -2
Viscosity Test  136 cm³/g 136 cm³/g DAM; formic acid 90%; ISO 307 1157 1628
Linear Mold Shrinkage, Flow  0.013 cm/cm 0.013 in/in DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse  0.013 cm/cm 0.013 in/in DAM; ISO 294-4 2577
 
Mechanical Properties Metric English Comments
Tensile Stress   14.2 MPa
@Strain 4.71 %,
Temperature 150 °C		 2060 psi
@Strain 4.71 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  16.3 MPa
@Strain 3.83 %,
Temperature 90.0 °C		 2360 psi
@Strain 3.83 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  16.7 MPa
@Strain 0.530 %,
Temperature 23.0 °C		 2420 psi
@Strain 0.530 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  19.3 MPa
@Strain 4.60 %,
Temperature 90.0 °C		 2800 psi
@Strain 4.60 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  20.1 MPa
@Strain 3.43 %,
Temperature 40.0 °C		 2920 psi
@Strain 3.43 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  23.9 MPa
@Strain 18.8 %,
Temperature 150 °C		 3470 psi
@Strain 18.8 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  25.5 MPa
@Strain 33.0 %,
Temperature 150 °C		 3700 psi
@Strain 33.0 %,
Temperature 302 °F		 DAM; ISO 11403-1 -2
  29.8 MPa
@Strain 3.02 %,
Temperature 23.0 °C		 4320 psi
@Strain 3.02 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  30.5 MPa
@Strain 14.3 %,
Temperature 90.0 °C		 4420 psi
@Strain 14.3 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  33.6 MPa
@Strain 25.2 %,
Temperature 90.0 °C		 4870 psi
@Strain 25.2 %,
Temperature 194 °F		 50%RH; ISO 11403-1 -2
  34.7 MPa
@Strain 17.4 %,
Temperature 90.0 °C		 5030 psi
@Strain 17.4 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  38.2 MPa
@Strain 30.2 %,
Temperature 90.0 °C		 5540 psi
@Strain 30.2 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  40.1 MPa
@Strain 12.7 %,
Temperature 40.0 °C		 5820 psi
@Strain 12.7 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  45.8 MPa
@Strain 22.0 %,
Temperature 40.0 °C		 6640 psi
@Strain 22.0 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  50.0 MPa
@Strain 11.9 %,
Temperature 23.0 °C		 7250 psi
@Strain 11.9 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  51.7 MPa
@Strain 3.40 %,
Temperature 40.0 °C		 7500 psi
@Strain 3.40 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  55.9 MPa
@Strain 1.93 %,
Temperature 23.0 °C		 8110 psi
@Strain 1.93 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  56.1 MPa
@Strain 20.4 %,
Temperature 23.0 °C		 8140 psi
@Strain 20.4 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  57.5 MPa
@Strain 29.2 %,
Temperature 23.0 °C		 8340 psi
@Strain 29.2 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  61.5 MPa
@Strain 10.3 %,
Temperature 40.0 °C		 8920 psi
@Strain 10.3 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  65.8 MPa
@Strain 17.9 %,
Temperature 40.0 °C		 9540 psi
@Strain 17.9 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  78.5 MPa
@Strain 3.39 %,
Temperature 23.0 °C		 11400 psi
@Strain 3.39 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  2.40 MPa
@Strain 0.202 %,
Time 3600 sec		 348 psi
@Strain 0.202 %,
Time 1.00 hour		 50%RH; isochronous; ISO 11403-1 -2
  2.40 MPa
@Strain 0.261 %,
Time 36000 sec		 348 psi
@Strain 0.261 %,
Time 10.0 hour		 50%RH; isochronous; ISO 11403-1 -2
  2.40 MPa
@Strain 0.340 %,
Time 360000 sec		 348 psi
@Strain 0.340 %,
Time 100 hour		 50%RH; isochronous; ISO 11403-1 -2
  2.40 MPa
@Strain 0.444 %,
Time 3.60e+6 sec		 348 psi
@Strain 0.444 %,
Time 1000 hour		 50%RH; isochronous; ISO 11403-1 -2
  2.40 MPa
@Strain 0.558 %,
Time 3.60e+7 sec		 348 psi
@Strain 0.558 %,
Time 10000 hour		 50%RH; isochronous; ISO 11403-1 -2
  9.60 MPa
@Strain 2.36 %,
Time 3.60e+7 sec		 1390 psi
@Strain 2.36 %,
Time 10000 hour		 50%RH; isochronous; ISO 11403-1 -2
  9.60 MPa
@Strain 1.89 %,
Time 3.60e+6 sec		 1390 psi
@Strain 1.89 %,
Time 1000 hour		 50%RH; isochronous; ISO 11403-1 -2
  9.60 MPa
@Strain 1.47 %,
Time 360000 sec		 1390 psi
@Strain 1.47 %,
Time 100 hour		 50%RH; isochronous; ISO 11403-1 -2
  9.60 MPa
@Strain 1.15 %,
Time 36000 sec		 1390 psi
@Strain 1.15 %,
Time 10.0 hour		 50%RH; isochronous; ISO 11403-1 -2
  9.60 MPa
@Strain 0.902 %,
Time 3600 sec		 1390 psi
@Strain 0.902 %,
Time 1.00 hour		 50%RH; isochronous; ISO 11403-1 -2
  19.2 MPa
@Time 3600 sec,
Strain 2.49 %		 2780 psi
@Time 1.00 hour,
Strain 2.49 %		 50%RH; isochronous; ISO 11403-1 -2
  19.2 MPa
@Strain 3.04 %,
Time 36000 sec		 2780 psi
@Strain 3.04 %,
Time 10.0 hour		 50%RH; isochronous; ISO 11403-1 -2
  19.2 MPa
@Strain 3.73 %,
Time 360000 sec		 2780 psi
@Strain 3.73 %,
Time 100 hour		 50%RH; isochronous; ISO 11403-1 -2
  19.2 MPa
@Strain 4.58 %,
Time 3.60e+6 sec		 2780 psi
@Strain 4.58 %,
Time 1000 hour		 50%RH; isochronous; ISO 11403-1 -2
  19.2 MPa
@Strain 5.50 %,
Time 3.60e+7 sec		 2780 psi
@Strain 5.50 %,
Time 10000 hour		 50%RH; isochronous; ISO 11403-1 -2
Tensile Strength, Yield  55.0 MPa 7980 psi 50%RH; ISO 527-1/-2
  85.0 MPa 12300 psi DAM; ISO 527-1/-2
Elongation at Break  20 % 20 % DAM; Nominal; ISO 527-1/-2
  >= 50 % >= 50 % 50%RH; Nominal; ISO 527-1/-2
Elongation at Yield  4.5 % 4.5 % DAM; ISO 527-1/-2
  4.5 % 4.5 % DAM; ISO 527-3
  25 % 25 % 50%RH; ISO 527-1/-2
Tensile Modulus  1.40 GPa 203 ksi 50%RH; ISO 527-1/-2
  3.10 GPa 450 ksi DAM; ISO 527-1/-2
Flexural Modulus  1.20 GPa 174 ksi 50%RH; ISO 178
  2.80 GPa 406 ksi DAM; ISO 178
Shear Modulus  0.1454 GPa
@Temperature 150 °C		 21.09 ksi
@Temperature 302 °F		 DAM; Dynamic; ISO 11403-1 -2
  0.170 GPa
@Temperature 110 °C		 24.7 ksi
@Temperature 230 °F		 DAM; Dynamic; ISO 11403-1 -2
  0.5141 GPa
@Temperature 60.0 °C		 74.57 ksi
@Temperature 140 °F		 DAM; Dynamic; ISO 11403-1 -2
  0.963 GPa
@Temperature 10.0 °C		 140 ksi
@Temperature 50.0 °F		 DAM; Dynamic; ISO 11403-1 -2
  0.9984 GPa
@Temperature -20.0 °C		 144.8 ksi
@Temperature -4.00 °F		 DAM; Dynamic; ISO 11403-1 -2
  1.065 GPa
@Temperature -50.0 °C		 154.5 ksi
@Temperature -58.0 °F		 DAM; Dynamic; ISO 11403-1 -2
Secant Modulus  0.184524 GPa
@Strain 25.2 %,
Temperature 40.0 °C		 26.7634 ksi
@Strain 25.2 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  0.245259 GPa
@Strain 23.2 %,
Temperature 23.0 °C		 35.5724 ksi
@Strain 23.2 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  0.315748 GPa
@Strain 12.7 %,
Temperature 40.0 °C		 45.7961 ksi
@Strain 12.7 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  0.319712 GPa
@Strain 20.8 %,
Temperature 40.0 °C		 46.3710 ksi
@Strain 20.8 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  0.420168 GPa
@Strain 11.9 %,
Temperature 23.0 °C		 60.9412 ksi
@Strain 11.9 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  0.586006 GPa
@Strain 3.43 %,
Temperature 40.0 °C		 84.9943 ksi
@Strain 3.43 %,
Temperature 104 °F		 50%RH; ISO 11403-1 -2
  0.597087 GPa
@Strain 10.3 %,
Temperature 40.0 °C		 86.6015 ksi
@Strain 10.3 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  0.986755 GPa
@Strain 3.02 %,
Temperature 23.0 °C		 143.119 ksi
@Strain 3.02 %,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1.52059 GPa
@Strain 3.40 %,
Temperature 40.0 °C		 220.546 ksi
@Strain 3.40 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  2.06427 GPa
@Strain 3.89 %,
Temperature 23.0 °C		 299.402 ksi
@Strain 3.89 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  2.89637 GPa
@Strain 1.93 %,
Temperature 23.0 °C		 420.089 ksi
@Strain 1.93 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  3.15094 GPa
@Strain 0.530 %,
Temperature 23.0 °C		 457.012 ksi
@Strain 0.530 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
Izod Impact, Notched (ISO)  5.00 kJ/m² 2.38 ft-lb/in² DAM; ISO 180/1A
  10.0 kJ/m² 4.76 ft-lb/in² 50%RH; ISO 180/1A
  5.00 kJ/m²
@Temperature -30.0 °C		 2.38 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 180/1A
  5.50 kJ/m²
@Temperature -40.0 °C		 2.62 ft-lb/in²
@Temperature -40.0 °F		 DAM; ISO 180/1A
  6.00 kJ/m²
@Temperature -30.0 °C		 2.86 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1A
Izod Impact, Unnotched (ISO)  NB NB DAM; ISO 180/1U
  NB NB 50%RH; ISO 180/1U
  300 kJ/m²
@Temperature -30.0 °C		 143 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1U
  NB
@Temperature -30.0 °C		 NB
@Temperature -22.0 °F		 50%RH; ISO 180/1U
Charpy Impact Unnotched  NB NB DAM; ISO 179/1eU
  NB NB 50%RH; ISO 179/1eU
  40.0 J/cm²
@Temperature -30.0 °C		 190 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eU
  NB
@Temperature -30.0 °C		 NB
@Temperature -22.0 °F		 50%RH; ISO 179/1eU
Charpy Impact, Notched  0.550 J/cm² 2.62 ft-lb/in² DAM; ISO 179/1eA
  1.20 J/cm² 5.71 ft-lb/in² 50%RH; ISO 179/1eA
  0.350 J/cm²
@Temperature -30.0 °C		 1.67 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 179/1eA
  0.450 J/cm²
@Temperature -30.0 °C		 2.14 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eA
Tensile Creep Modulus, 1 hour  618.557 MPa
@Pressure 24.0 MPa,
Temperature 23.0 °C		 89714.3 psi
@Pressure 3480 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  744.963 MPa
@Pressure 20.0 MPa,
Temperature 23.0 °C		 108048 psi
@Pressure 2900 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  904.333 MPa
@Pressure 15.0 MPa,
Temperature 23.0 °C		 131163 psi
@Pressure 2180 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1054.5 MPa
@Pressure 10.0 MPa,
Temperature 23.0 °C		 152940 psi
@Pressure 1450 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1159.32 MPa
@Pressure 5.00 MPa,
Temperature 23.0 °C		 168145 psi
@Pressure 725 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1190 MPa
@Time 3600 sec		 173000 psi
@Time 1.00 hour		 50%RH; ISO 899-1
Tensile Creep Modulus, 1000 hours  366.412 MPa
@Pressure 24.0 MPa,
Temperature 23.0 °C		 53143.7 psi
@Pressure 3480 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  410.846 MPa
@Pressure 20.0 MPa,
Temperature 23.0 °C		 59588.3 psi
@Pressure 2900 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  461.905 MPa
@Pressure 15.0 MPa,
Temperature 23.0 °C		 66993.8 psi
@Pressure 2180 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  505.277 MPa
@Pressure 10.0 MPa,
Temperature 23.0 °C		 73284.4 psi
@Pressure 1450 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  533.046 MPa
@Pressure 5.00 MPa,
Temperature 23.0 °C		 77311.9 psi
@Pressure 725 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  540 MPa
@Time 3.60e+6 sec		 78300 psi
@Time 1000 hour		 50%RH; ISO 899-1
 
Electrical Properties Metric English Comments
Volume Resistivity  1.00e+13 ohm-cm 1.00e+13 ohm-cm 50%RH; IEC 60093
  1.00e+15 ohm-cm 1.00e+15 ohm-cm DAM; IEC 60093
Surface Resistance  1.00e+12 ohm 1.00e+12 ohm DAM; ASTM D257
Dielectric Constant  3.5
@Frequency 1.00e+6 Hz		 3.5
@Frequency 1.00e+6 Hz		 DAM; ASTM D150
  3.5
@Frequency 1.00e+6 Hz		 3.5
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  3.6
@Frequency 100 Hz		 3.6
@Frequency 100 Hz		 DAM; ASTM D150
  3.8
@Frequency 100 Hz		 3.8
@Frequency 100 Hz		 DAM; IEC 60250
  4.0
@Frequency 1.00e+6 Hz		 4.0
@Frequency 1.00e+6 Hz		 50%RH; IEC 60250
  12.8
@Frequency 100 Hz		 12.8
@Frequency 100 Hz		 50%RH; IEC 60250
Dielectric Strength  28.0 kV/mm 711 kV/in 50%RH; IEC 60243-1
  31.0 kV/mm 787 kV/in DAM; IEC 60243-1
Dissipation Factor  0.0075
@Frequency 100 Hz		 0.0075
@Frequency 100 Hz		 DAM; IEC 60250
  0.0165
@Frequency 1.00e+6 Hz		 0.0165
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  0.070
@Frequency 1.00e+6 Hz		 0.070
@Frequency 1.00e+6 Hz		 50%RH; IEC 60250
  0.58
@Frequency 100 Hz		 0.58
@Frequency 100 Hz		 50%RH; IEC 60250
Comparative Tracking Index  600 V 600 V DAM; IEC 60112
  >= 600 V
@Thickness 3.00 mm		 >= 600 V
@Thickness 0.118 in		 DAM; UL 746A
 
Thermal Properties Metric English Comments
CTE, linear, Parallel to Flow  100 µm/m-°C 55.6 µin/in-°F DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow  110 µm/m-°C 61.1 µin/in-°F DAM; ISO 11359-1/-2
Specific Heat Capacity  2.79 J/g-°C 0.667 BTU/lb-°F  
Thermal Conductivity  0.160 W/m-K 1.11 BTU-in/hr-ft²-°F of melt
Melting Point  262 °C 504 °F DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 0.46 MPa (66 psi)  200 °C 392 °F DAM; ISO 75-1/-2
Deflection Temperature at 1.8 MPa (264 psi)  70.0 °C 158 °F DAM; ISO 75-1/-2
Vicat Softening Point  240 °C 464 °F DAM; 50°C/h 50N; ISO 306
Glass Transition Temp, Tg  60.0 °C 140 °F DAM; 10°C/min; ISO 11357-1/-2
Flammability, UL94  V-2
@Thickness 1.50 mm		 V-2
@Thickness 0.0591 in		 DAM; IEC 60695-11-10
  V-2
@Thickness 0.700 mm		 V-2
@Thickness 0.0276 in		 DAM; IEC 60695-11-10
Oxygen Index  28 % 28 % DAM; ISO 4589-1/-2
 
Descriptive Properties
Additives Lubricants  
  Release agent  
Delivery form Pellets  
Eff. thermal diffusivity 5.00E-08 m²/s  
Emission of organic compounds 2.1 µgC/g VDA 277
Odour class 2.5 VDA 270
Part Marking Code >PA66< ISO 11469
Processing Coatable  
  Injection Moulding  
  Other Extrusion  
Regional Availability Asia Pacific  
  Europe  
  Global  
  Near East/Africa  
  North America  
  South and Central America  
Resin Identification PA66  
Special characteristics Heat stabilised or stable to heat  
UL recognition UL DAM
 
导电尼龙66：具有良好的耐磨性、耐热性、耐油性及耐化学药品性，还大大降低了原材料的吸水率和收缩率,具有优良的尺寸稳定性及优异的机械强度。能满足静电消散和静电放电(ESD)防护的要求。这些特殊改性材料经特殊配制，适用于从100到1012欧姆/平方(ohms/sq)的表面电阻范围，可用于注塑及挤出等成型。有很多超越金属和涂装的优点:零件重量较轻，较易处理，运输成本较低。它们的装配简便，制造成本较低，并且较不会受到撞凹，割损和刮伤。为了标识或美观目的，一些材料可被预先染色，避免费时且昂贵的两次着色加工。
 
颗粒01
上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各位客户前来咨询：
联系人： 夏先生  
手  机：13501802636   
QQ    ：205730283  
邮 箱 ：205730283@qq.com 

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/news/

本文链接: http://www.su-jiao.com/news/show-25468.html

免责声明: 本文 PA66 103HSL NC010 低温特性佳 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他资讯信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4