- 密度 [g/cm3]: 1.03
- 吸水率 [%]: 1.4
- 缺口冲击强度: 1.0
- 拉伸强度 [MPa]: 60.0
- 弯曲模量 [MPa]: 2.00
- 热变形温度 [℃]: 190.0
| Physical Properties | Metric | English | Comments | ||
|---|---|---|---|---|---|
| Density | 1.03 g/cc | 0.0372 lb/in³ | ISO R 1183 | ||
| Moisture Absorption at Equilibrium | 0.90 % | 0.90 % | DIN 53473 | ||
| Water Absorption at Saturation | 1.4 % @Temperature 20.0 °C | 1.4 % @Temperature 68.0 °F | ISO R 62 | ||
| Mechanical Properties | Metric | English | Comments | ||
| Ball Indentation Hardness | 100 MPa | 14500 psi | Hc 30; ISO 2039; partially | ||
| Tensile Strength, Yield | 60.0 MPa | 8700 psi | ISO-DIS 527 | ||
| Tensile Modulus | 2.00 GPa | 290 ksi | DIN 53457 | ||
| Flexural Strength | 90.0 MPa | 13100 psi | DIN 54352 | ||
| Flexural Modulus | 2.00 GPa | 290 ksi | DIN 53457 | ||
| Compressive Strength | 38.0 MPa | 5510 psi | 5% pressing; EN ISO 604 | ||
| 56.0 MPa | 8120 psi | 10% pressing; EN ISO 604 | |||
| 76.0 MPa | 11000 psi | 20% pressing; EN ISO 604 | |||
| Izod Impact, Notched (ISO) | >= 1.00 kJ/m² | >= 0.476 ft-lb/in² | DIN 53453 | ||
| Izod Impact Resistance | NB | NB | swinging hammer 0,1 DIN 51222; DIN 53453 | ||
| Coefficient of Friction, Dynamic | 0.38 | 0.38 | no lube; Steel 2162, Rvst=2E-6m, p=0.05 Mpa, v=0.6 m/s, t=40°C | ||
| Tear Strength Test | >= 0.20 | >= 0.20 | ISO-DIS 527 | ||
| Electrical Properties | Metric | English | Comments | ||
| Volume Resistivity | 1.00e+14 ohm-cm | 1.00e+14 ohm-cm | DIN 53482 | ||
| Surface Resistance | 1.00e+12 ohm | 1.00e+12 ohm | DIN 53482 | ||
| Dielectric Constant | 3.5 | 3.5 | DIN 53483 | ||
| Dielectric Strength | 35.0 kV/mm | 889 kV/in | DIN 53481 | ||
| Dielectric Loss Index | 0.040 | 0.040 | DIN 53483 | ||
| Thermal Properties | Metric | English | Comments | ||
| CTE, linear | 80.0 - 100 µm/m-°C @Temperature 20.0 - 100 °C | 44.4 - 55.6 µin/in-°F @Temperature 68.0 - 212 °F | DIN 53752 | ||
| Specific Heat Capacity | 2.50 J/g-°C | 0.598 BTU/lb-°F | |||
| Thermal Conductivity | 0.250 W/m-K | 1.74 BTU-in/hr-ft²-°F | DIN 52612 | ||
| Melting Point | 190 °C | 374 °F | ISO R 1218 | ||
| Maximum Service Temperature, Air | 120 °C | 248 °F | Continuous | ||
| 150 °C | 302 °F | Intermittent | |||
| Deflection Temperature at 0.46 MPa (66 psi) | 190 °C | 374 °F | V-notch; ISO R 75 | ||
| Minimum Service Temperature, Air | -40.0 °C | -40.0 °F | Continuous | ||
| Descriptive Properties | |||||
| Creepage/leakage Resistance | KA3b | DIN 53480 | |||