塑胶原料之家
  1. 首页
  2. 资讯
  3. 产品资讯
  4. PA66 135F NC010 耐韧、耐冲击性特优

PA66 135F NC010 耐韧、耐冲击性特优

PA66 135F NC010 物理化学性：PA66塑胶原料为半透明或不透明乳白包或带黄色颗粒状结晶形聚合物，PA66 135F NC010具有可塑性。密度（g/cm3） 1．10-1．14；拉伸强度(MPa) 60. 0-80．0；洛氏硬度118；PA66 135F NC010熔点252℃；脆化温度-30℃；热分解温度大于350℃；连续耐热80-120℃；冲击强度（kJ/m2） 60-100；静弯曲强度(MPa) 1 00-120；马丁耐热(℃) 50-60；弯曲弹性模量 (MPa) 2000～3000
 PA66 135F NC010 注模条件：注射压力。通常在750~1250bar，取决于材料和产品设计。注射速度高速（对于增强型材料应稍低一些）。流道和浇口:由于PA66的凝固时间很短，因此浇口的位置非常重要。浇口孔径不要小于0.5*t（这里t为塑件厚度）。
 
Physical Properties Metric English Comments
Density  1.01 g/cc 0.0365 lb/in³  
  1.14 g/cc 0.0412 lb/in³ DAM; ISO 1183
Water Absorption  8.5 %
@Thickness 2.00 mm		 8.5 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Moisture Absorption  2.70 %
@Thickness 2.00 mm		 2.70 %
@Thickness 0.0787 in		 DAM; Sim. to ISO 62
Viscosity    64000 cP
@Shear Rate 5000 1/s,
Temperature 315 °C		 64000 cP
@Shear Rate 5000 1/s,
Temperature 599 °F		 ISO 11403-1 -2
  83000 cP
@Shear Rate 5000 1/s,
Temperature 295 °C		 83000 cP
@Shear Rate 5000 1/s,
Temperature 563 °F		 ISO 11403-1 -2
  105000 cP
@Shear Rate 5000 1/s,
Temperature 275 °C		 105000 cP
@Shear Rate 5000 1/s,
Temperature 527 °F		 ISO 11403-1 -2
  134000 cP
@Shear Rate 500 1/s,
Temperature 315 °C		 134000 cP
@Shear Rate 500 1/s,
Temperature 599 °F		 ISO 11403-1 -2
  195000 cP
@Shear Rate 500 1/s,
Temperature 295 °C		 195000 cP
@Shear Rate 500 1/s,
Temperature 563 °F		 ISO 11403-1 -2
  284000 cP
@Shear Rate 500 1/s,
Temperature 275 °C		 284000 cP
@Shear Rate 500 1/s,
Temperature 527 °F		 ISO 11403-1 -2
Viscosity Test  150 cm³/g 150 cm³/g DAM; ISO 307 1157 1628
Linear Mold Shrinkage, Flow  0.0070 cm/cm 0.0070 in/in DAM; ISO 294-4 2577
Linear Mold Shrinkage, Transverse  0.013 cm/cm 0.013 in/in DAM; ISO 294-4 2577
 
Mechanical Properties Metric English Comments
Hardness, Rockwell M  64 64 50%RH; ISO 2039-2
  87 87 DAM; ISO 2039-2
Hardness, Rockwell R  116 116 50%RH; ISO 2039-2
  123 123 DAM; ISO 2039-2
Tensile Stress    7.47 MPa
@Strain 0.960 %,
Temperature 90.0 °C		 1080 psi
@Strain 0.960 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  11.4 MPa
@Strain 0.480 %,
Temperature 40.0 °C		 1650 psi
@Strain 0.480 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  17.8 MPa
@Strain 2.40 %,
Temperature 90.0 °C		 2580 psi
@Strain 2.40 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  18.0 MPa
@Strain 0.480 %,
Temperature 23.0 °C		 2610 psi
@Strain 0.480 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  22.8 MPa
@Strain 0.550 %,
Temperature 0.000 °C		 3310 psi
@Strain 0.550 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  24.5 MPa
@Strain 3.84 %,
Temperature 90.0 °C		 3550 psi
@Strain 3.84 %,
Temperature 194 °F		 DAM; ISO 11403-1 -2
  26.5 MPa
@Strain 0.630 %,
Temperature -20.0 °C		 3840 psi
@Strain 0.630 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  41.6 MPa
@Strain 1.92 %,
Temperature 40.0 °C		 6030 psi
@Strain 1.92 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  60.5 MPa
@Strain 3.36 %,
Temperature 40.0 °C		 8770 psi
@Strain 3.36 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  65.5 MPa
@Strain 1.92 %,
Temperature 23.0 °C		 9500 psi
@Strain 1.92 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  65.7 MPa
@Strain 4.80 %,
Temperature 40.0 °C		 9530 psi
@Strain 4.80 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  82.7 MPa
@Strain 2.20 %,
Temperature 0.000 °C		 12000 psi
@Strain 2.20 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  92.9 MPa
@Strain 3.36 %,
Temperature 23.0 °C		 13500 psi
@Strain 3.36 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  95.4 MPa
@Strain 2.52 %,
Temperature -20.0 °C		 13800 psi
@Strain 2.52 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  117 MPa
@Strain 3.85 %,
Temperature 0.000 °C		 17000 psi
@Strain 3.85 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  133 MPa
@Strain 4.41 %,
Temperature -20.0 °C		 19300 psi
@Strain 4.41 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
   3.00 MPa
@Strain 0.146 %,
Time 3600 sec		 435 psi
@Strain 0.146 %,
Time 1.00 hour		 50%RH; isochronous; ISO 11403-1 -2
  3.00 MPa
@Strain 0.165 %,
Time 36000 sec		 435 psi
@Strain 0.165 %,
Time 10.0 hour		 50%RH; isochronous; ISO 11403-1 -2
  3.00 MPa
@Strain 0.192 %,
Time 360000 sec		 435 psi
@Strain 0.192 %,
Time 100 hour		 50%RH; isochronous; ISO 11403-1 -2
  3.00 MPa
@Strain 0.231 %,
Time 3.60e+6 sec		 435 psi
@Strain 0.231 %,
Time 1000 hour		 50%RH; isochronous; ISO 11403-1 -2
  3.00 MPa
@Strain 0.297 %,
Time 3.60e+7 sec		 435 psi
@Strain 0.297 %,
Time 10000 hour		 50%RH; isochronous; ISO 11403-1 -2
  12.0 MPa
@Strain 1.45 %,
Time 3.60e+7 sec		 1740 psi
@Strain 1.45 %,
Time 10000 hour		 50%RH; isochronous; ISO 11403-1 -2
  12.0 MPa
@Strain 1.18 %,
Time 3.60e+6 sec		 1740 psi
@Strain 1.18 %,
Time 1000 hour		 50%RH; isochronous; ISO 11403-1 -2
  12.0 MPa
@Strain 0.947 %,
Time 360000 sec		 1740 psi
@Strain 0.947 %,
Time 100 hour		 50%RH; isochronous; ISO 11403-1 -2
  12.0 MPa
@Strain 0.772 %,
Time 36000 sec		 1740 psi
@Strain 0.772 %,
Time 10.0 hour		 50%RH; isochronous; ISO 11403-1 -2
  12.0 MPa
@Strain 0.656 %,
Time 3600 sec		 1740 psi
@Strain 0.656 %,
Time 1.00 hour		 50%RH; isochronous; ISO 11403-1 -2
Tensile Strength, Yield  67.0 MPa 9720 psi 50%RH; ISO 527-1/-2
  96.0 MPa 13900 psi DAM; ISO 527-1/-2
Elongation at Break  13 % 13 % DAM; Nominal; ISO 527-1/-2
  50 % 50 % 50%RH; Nominal; ISO 527-1/-2
Elongation at Yield  4.5 % 4.5 % DAM; ISO 527-1/-2
  4.5 % 4.5 % DAM; ISO 527-3
  18 % 18 % 50%RH; ISO 527-1/-2
Tensile Modulus  2.00 GPa 290 ksi 50%RH; ISO 527-1/-2
  3.60 GPa 522 ksi DAM; ISO 527-1/-2
Shear Modulus    0.175 GPa
@Temperature 160 °C		 25.4 ksi
@Temperature 320 °F		 DAM; Dynamic; ISO 11403-1 -2
  0.214 GPa
@Temperature 120 °C		 31.0 ksi
@Temperature 248 °F		 DAM; Dynamic; ISO 11403-1 -2
  0.449 GPa
@Temperature 70.0 °C		 65.1 ksi
@Temperature 158 °F		 DAM; Dynamic; ISO 11403-1 -2
  1.0685 GPa
@Temperature 20.0 °C		 154.98 ksi
@Temperature 68.0 °F		 DAM; Dynamic; ISO 11403-1 -2
  1.171 GPa
@Temperature -20.0 °C		 169.8 ksi
@Temperature -4.00 °F		 DAM; Dynamic; ISO 11403-1 -2
  1.259 GPa
@Temperature -50.0 °C		 182.6 ksi
@Temperature -58.0 °F		 DAM; Dynamic; ISO 11403-1 -2
Shear Strength    0.0670 MPa
@Shear Rate 500 1/s,
Temperature 315 °C		 9.72 psi
@Shear Rate 500 1/s,
Temperature 599 °F		 ISO 11403-1 -2
  0.0975 MPa
@Shear Rate 500 1/s,
Temperature 295 °C		 14.1 psi
@Shear Rate 500 1/s,
Temperature 563 °F		 ISO 11403-1 -2
  0.142 MPa
@Shear Rate 500 1/s,
Temperature 275 °C		 20.6 psi
@Shear Rate 500 1/s,
Temperature 527 °F		 ISO 11403-1 -2
Secant Modulus    1.65625 GPa
@Strain 3.84 %,
Temperature 40.0 °C		 240.222 ksi
@Strain 3.84 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  2.16667 GPa
@Strain 1.92 %,
Temperature 40.0 °C		 314.254 ksi
@Strain 1.92 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  2.375 GPa
@Strain 0.480 %,
Temperature 40.0 °C		 344.5 ksi
@Strain 0.480 %,
Temperature 104 °F		 DAM; ISO 11403-1 -2
  2.51562 GPa
@Strain 3.84 %,
Temperature 23.0 °C		 364.866 ksi
@Strain 3.84 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  2.7381 GPa
@Strain 5.04 %,
Temperature -20.0 °C		 397.13 ksi
@Strain 5.04 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  2.77273 GPa
@Strain 4.40 %,
Temperature 0.000 °C		 402.157 ksi
@Strain 4.40 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  3.41146 GPa
@Strain 1.92 %,
Temperature 23.0 °C		 494.798 ksi
@Strain 1.92 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  3.75 GPa
@Strain 0.480 %,
Temperature 23.0 °C		 544 ksi
@Strain 0.480 %,
Temperature 73.4 °F		 DAM; ISO 11403-1 -2
  3.75909 GPa
@Strain 2.20 %,
Temperature 0.000 °C		 545.218 ksi
@Strain 2.20 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  3.78571 GPa
@Strain 2.52 %,
Temperature -20.0 °C		 549.079 ksi
@Strain 2.52 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
  4.14545 GPa
@Strain 0.550 %,
Temperature 0.000 °C		 601.256 ksi
@Strain 0.550 %,
Temperature 32.0 °F		 DAM; ISO 11403-1 -2
  4.20635 GPa
@Strain 0.630 %,
Temperature -20.0 °C		 610.089 ksi
@Strain 0.630 %,
Temperature -4.00 °F		 DAM; ISO 11403-1 -2
Izod Impact, Notched (ISO)  3.50 kJ/m² 1.67 ft-lb/in² DAM; ISO 180/1A
  9.00 kJ/m² 4.28 ft-lb/in² 50%RH; ISO 180/1A
   2.00 kJ/m²
@Temperature -30.0 °C		 0.952 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 180/1A
  3.00 kJ/m²
@Temperature -30.0 °C		 1.43 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 180/1A
Charpy Impact Unnotched  NB NB DAM; ISO 179/1eU
  NB NB 50%RH; ISO 179/1eU
   NB
@Temperature -30.0 °C		 NB
@Temperature -22.0 °F		 DAM; ISO 179/1eU
  NB
@Temperature -30.0 °C		 NB
@Temperature -22.0 °F		 50%RH; ISO 179/1eU
Charpy Impact, Notched  0.400 J/cm² 1.90 ft-lb/in² DAM; ISO 179/1eA
  0.900 J/cm² 4.28 ft-lb/in² 50%RH; ISO 179/1eA
   0.250 J/cm²
@Temperature -30.0 °C		 1.19 ft-lb/in²
@Temperature -22.0 °F		 50%RH; ISO 179/1eA
  0.300 J/cm²
@Temperature -30.0 °C		 1.43 ft-lb/in²
@Temperature -22.0 °F		 DAM; ISO 179/1eA
Tensile Creep Modulus, 1 hour    1619.87 MPa
@Pressure 15.0 MPa,
Temperature 23.0 °C		 234943 psi
@Pressure 2180 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1684.54 MPa
@Pressure 14.0 MPa,
Temperature 23.0 °C		 244322 psi
@Pressure 2030 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1829.27 MPa
@Pressure 12.0 MPa,
Temperature 23.0 °C		 265314 psi
@Pressure 1740 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1934.32 MPa
@Pressure 10.0 MPa,
Temperature 23.0 °C		 280550 psi
@Pressure 1450 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1985.1 MPa
@Pressure 8.00 MPa,
Temperature 23.0 °C		 287910 psi
@Pressure 1160 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  2006.69 MPa
@Pressure 6.00 MPa,
Temperature 23.0 °C		 291046 psi
@Pressure 870 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  2036.34 MPa
@Pressure 4.00 MPa,
Temperature 23.0 °C		 295347 psi
@Pressure 580 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  2069.34 MPa
@Pressure 2.00 MPa,
Temperature 23.0 °C		 300133 psi
@Pressure 290 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  2000 MPa
@Time 3600 sec		 290000 psi
@Time 1.00 hour		 50%RH; ISO 899-1
Tensile Creep Modulus, 1000 hours    847.458 MPa
@Pressure 15.0 MPa,
Temperature 23.0 °C		 122914 psi
@Pressure 2180 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  894.057 MPa
@Pressure 14.0 MPa,
Temperature 23.0 °C		 129672 psi
@Pressure 2030 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1016.95 MPa
@Pressure 12.0 MPa,
Temperature 23.0 °C		 147496 psi
@Pressure 1740 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1164.84 MPa
@Pressure 10.0 MPa,
Temperature 23.0 °C		 168946 psi
@Pressure 1450 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1268.05 MPa
@Pressure 8.00 MPa,
Temperature 23.0 °C		 183915 psi
@Pressure 1160 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1276.6 MPa
@Pressure 6.00 MPa,
Temperature 23.0 °C		 185160 psi
@Pressure 870 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1285.99 MPa
@Pressure 4.00 MPa,
Temperature 23.0 °C		 186517 psi
@Pressure 580 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1309.32 MPa
@Pressure 2.00 MPa,
Temperature 23.0 °C		 189901 psi
@Pressure 290 psi,
Temperature 73.4 °F		 50%RH; ISO 11403-1 -2
  1280 MPa
@Time 3.60e+6 sec		 186000 psi
@Time 1000 hour		 50%RH; ISO 899-1
 
Electrical Properties Metric English Comments
Dielectric Constant    3.8
@Frequency 1.00e+6 Hz		 3.8
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  3.9
@Frequency 1.00e+6 Hz		 3.9
@Frequency 1.00e+6 Hz		 50%RH; IEC 60250
  3.9
@Frequency 100 Hz		 3.9
@Frequency 100 Hz		 DAM; IEC 60250
  8.7
@Frequency 100 Hz		 8.7
@Frequency 100 Hz		 50%RH; IEC 60250
Dissipation Factor    0.0070
@Frequency 100 Hz		 0.0070
@Frequency 100 Hz		 DAM; IEC 60250
  0.020
@Frequency 1.00e+6 Hz		 0.020
@Frequency 1.00e+6 Hz		 DAM; IEC 60250
  0.060
@Frequency 1.00e+6 Hz		 0.060
@Frequency 1.00e+6 Hz		 50%RH; IEC 60250
  0.24
@Frequency 100 Hz		 0.24
@Frequency 100 Hz		 50%RH; IEC 60250
Comparative Tracking Index  600 V 600 V DAM; IEC 60112
 
Thermal Properties Metric English Comments
CTE, linear, Parallel to Flow  121 µm/m-°C 67.2 µin/in-°F DAM; ISO 11359-1/-2
CTE, linear, Transverse to Flow  121 µm/m-°C 67.2 µin/in-°F DAM; ISO 11359-1/-2
Specific Heat Capacity  2.79 J/g-°C 0.667 BTU/lb-°F  
Thermal Conductivity  0.160 W/m-K 1.11 BTU-in/hr-ft²-°F of melt
Melting Point  263 °C 505 °F DAM; 10°C/min; ISO 11357-1/-3
Deflection Temperature at 0.46 MPa (66 psi)  210 °C 410 °F DAM; ISO 75-1/-2
Deflection Temperature at 1.8 MPa (264 psi)  75.0 °C 167 °F DAM; ISO 75-1/-2
Vicat Softening Point  245 °C 473 °F DAM; 50°C/h 50N; ISO 306
Glass Transition Temp, Tg  60.0 °C 140 °F DAM; 10°C/min; ISO 11357-1/-2
Flammability, UL94    V-2
@Thickness 1.50 mm		 V-2
@Thickness 0.0591 in		 DAM; IEC 60695-11-10
  V-2
@Thickness 0.700 mm		 V-2
@Thickness 0.0276 in		 DAM; IEC 60695-11-10
 
Descriptive Properties
Additives Lubricants  
  Release agent  
Delivery form Pellets  
Part Marking Code >PA66< ISO 11469
Processing Injection Moulding  
Regional Availability Asia Pacific  
  Europe  
  Near East/Africa  
Resin Identification PA66  
UL recognition UL DAM
 
 
化学式：[-NH（CH2）6－NHCO(CH2)4CO]n－能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀
颗粒03
 
上海松翰塑化科技有限公司，供应原料，品质真实,物实价廉。
PA6T,46,9T、PC、PC/ABS、PBT、ABS、PPA、PPS、POM、PMMA、TPE、PPO、LCP液晶聚合物。
欢迎各位客户前来咨询：
联系人： 夏先生  
手  机：13501802636   
QQ    ：205730283  
邮 箱 ：205730283@qq.com 

转载请注明: 转自中国塑胶原料之家 http://www.su-jiao.com/news/

本文链接: http://www.su-jiao.com/news/show-25471.html

免责声明: 本文 PA66 135F NC010 耐韧、耐冲击性特优 仅代表作者个人观点，中国塑胶原料之家无关。中国塑胶原料之家网所转载的内容，其版权均由原作者和资料提供方所拥有！如因作品版权问题需要处理，请与我们联络

该类别其他资讯信息

塑胶原料之家，专业塑料网站、原料报价网站，免费发布塑胶供求信息。塑胶原料之家为您提供塑料供应、塑料求购、塑料行情、塑料展会、塑料原料资讯服务。

2008-2015 塑料|塑胶原料|物性表大全|UL黄卡|SGS报告查询|最新价格--塑胶原料之家

沪ICP备15027283号-4